Kyocera - Основной каталог 2011-2012 ENG

                                                                            для заказа - kyocera@kyocera-tools.ru

         Cut-Off Toolholders (for sub spindle tooling)

           KTKFS (For Small diameter cut-off)

                                                                                                                          L4

                Sub Spindle Dia.                                              H1 B H1 B                                                  F1 1

                     40 -12A,-16A                                                                                                                             2
                        50 -12B,-16B
                                                                                                                    30 L3
                                                                                                      L1

                                                                                                                                         Dsmax

                                                       Right-hand Shown                                                                                                     R-hand Insert for R-hand Toolholder.
                                                                                                                                      T
                                                                                                                                         1 F1
                Sub Spindle Dia.
                                                                                                                                                               2
                     40 -12A-16A
                        50 -12B-16B                                                                                 30 L3
                                                                                                      L1

                                                                                                                               Dsmax

H                                                                                                                                        h                                 KTKFS 1010K-12A
                                                                                                                                                     2                     KTKFS 1010K-16A
                                                               Left-hand Shown                                                                                  L2

                                                                                                                                                                        L-hand Insert for L-hand Toolholder.

Cut-off  Toolholder Dimensions                 Cutting                                           Dimension (mm)                                           Spare Parts                                     Applicable
                Description           Std. Dia.                                                                                                 Clamp Screw Wrench                                          Inserts
                                      R L Dsmax H1=h B                                                            *                                                                                            H9
                                                                                                 L1 L2 L3 L4 F1 T

         KTKFS  1010K-12A                                                                10 10 120 15 22
                1212F-12A
                1212K-12B                              6~12                              12  12  85   -                  26           5  6 SB-4050TRN             LTW-10S                                 TKFS12
                                                                                                 120               26

         KTKFS  1010K-16A                                                                10  10 120 20             22
                1212F-16A                                                                          85
                1212K-16B                              14~16                             12 12 120 - 26                   30          5  8 SB-4050TRN             LTW-10S                                 TKFS16

         • Dimension T shows the distance from the Toolholder to the cutting edge. H8 for the actual cutting diameter.                   For recommended cutting conditions, see page H11
         • Cutting diameter (Dmax) depends on the insert grooving width.

         * Only R-hand is available for L4 dimension.

         TKFS (Dmax)                                                                                                                    Main spindle                                                   Main spindle
                                                                                                                                                                                                                          Sub spindle
                             Insert                                                      Description  Dimension (mm)                                    Sub spindle
                                                                                                               Dsmax                                                                                        Fig.2
                Handed insert indicates Left-hand
                       HT
                                                                              0.03

                                                                           W

                                                                                                                                          1
                                                                                                                                Dsmax
                                                                                                                                                                                                       1
                                                                                                                                                                                 Dsmax
                                                       d                                 TKFS12 100-S 1.0              6
                                                                           r                            150-S 1.5      9

                                                       r

                                                                                                 200-S 2.0 12

                                                                                                TKFS16 150-S 1.5   14
                                                                                         Dsmax 200-S 2.0           16

         Note) As Fig.2 shows, the cutting diameter of the insert is indicated when the top of the cutting edge                          Fig.1
                progresses 1mm from the center.

         As Fig.1 shows, use KTKFL (L-hand) for the distance between main spindle and sub spindle.
         As Fig.2 shows, KTKFS is recommended for small diameters and for the short distance between the main spindle and sub
         spindle.

                                                                                                                                                                  : Std. Item : Check Availability

H10                                                    для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru