Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Grooving Inserts
Applicable Inserts P Carbon Steel / Alloy Steel Classification of usage
M Stainless Steel
(mm) K Cast Iron : Continuous-Light Interruption /
N Non-ferrous Metals 1st Choice
Description ALH S Titanium Alloy : Continuous-Light Interruption /
H Hard materials (under 40HRC) 2nd Choice
GVF …-100AA Hard materials (over 40HRC) : Continuous / 1st Choice
(Previous : Continuous / 2nd Choice
…-200AA 4.3 12 4.5 Dimension
(mm) PCD
…-300AA
Applicable
PVD Toolholder
TN90Cermet Coated
TC40 Carbide
TC60
Insert Description Description) W B r PR630
PR930
R-hand shown KW10 Carbide
KPD001
KPD010
Ref. Page for
Toolholder
HA r 100-005AA GVF 100AA 1.00 GFVS …-08AA
200-005AA 200AA 2.00 2.2 0.05 GFVT …-08AA G76
GVF
2r
B W 0.05
L
10 10 300-005AA 300AA 3.00
Dimension B: shows available grooving depth.
GVF …005AA inserts are not compatible with GVF …A (see page G83) inserts because their Side Relief Angle is 10.
Face Grooving Diameter of GFVS-AA (also GFVT-AA) G
Description Face Grooving If the first groove is machined larger than the MIN.
Dia. D Applicable Inserts value then there is no MAX limit to the further groove machining.
GFVS 1010F-08AA When machining towards the outer diameter then there
is no MAX limit to the further groove machining.
1212H-08AA 8 GVFL/R100AA Grooving
1616H-08AA ~
2020K-08AA (0) ( ) GVFL/R300AA
2525M-08AA
Refers to the machining of the initial groove with MIN.8. When widening the groove width to inner diameter.
For machining up to the center of the workpiece
If the initial groove is made smaller than this, regardless of insert width.
the toolholder interferes with the workpiece.
8 (MIN.Face Grooving Dia) 6 (Boss Dia.) 8 (MIN.Face Grooving Dia) 2 (Boss Dia.) 8 (MIN.Face Grooving Dia) 8 (MIN.Face Grooving Dia)
1 (width)
3 (width) 4 4
(Widening the Groove (Widening the Groove
Installing GVFL100AA Installing GVFL300AA Width to Center) Width to Center)
Installing GVFL100AA Installing GVFL300AA
Recommended Cutting Conditions (GFVS-AA / GFVT-AA)
Recommended Insert Grade (Cutting Speed: m/min) Grooving Longitudinal turning*
PVD Coated Carbide Carbide
Workpiece PR630 Remarks
PR930
Material KW10 f ap f
(mm) (mm/rev)
(mm/rev)
Carbon Steel / Alloy Steel 50 100 50 100 0.01 0.05 Max.0.5 0.01 0.05
0.01 0.03 Max.0.3 0.01 0.02 Coolant
Stainless Steel 50 80 50 80 0.01 0.08 Max.0.5 0.01 0.08
Non-ferrous Metals 200 : 1st Recommendation : 2nd Recommendation
* ap has to be set for less than corner-R(r) when Longitudinal turning of
edge width 1.0 mm (GVF 100AA).
: Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) Inserts are sold
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru in 10 piece boxes.
G77