Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Face Grooving Toolholders [GVF Insert]
GFV
T
(ToFaocueteGr droiao.v)ing Dia. D 2F L2 L1 H1 H3 B Fa(cTeoGouroteorvidniga.D) ia. D
HeaDd1dia1meterh Head diaDm1eter
L3
GFV 2020K 201A L3
GFV 2525M 201A
Shows right Figure.
Right-hand Shown Left-hand Shown
R-hand Insert is for R-hand Toolholder, L-hand Insert is for L-hand Toolholder.
G Toolholder Dimensions Dimension (mm) Face Grooving Dia. Spare Parts
D
Std. Clamp Set Wrench Applicable
Description Inserts
R L H1 h H3 B L1 L2 L3 F T D1 MIN. MAX. G83
LW
Grooving FT
GFV 2020K-201A 20 21 6.5 20 125 20 19 25 2.2 40 20 CPS-5V - FT-15 GVF 200A~340A
GFV 2525M-201A 25 26 25 150 23 22 32 (12) - CPS-6V LW-3 GVF 100AR~150AR
2020K-351B - CPS-8V LW-4 GVF 250B~350B
GFV 2525M-351B 20 21 20 125 28 26 25 4.6 35 50 GVF 150BR
2020K-352B 25 26 25 150 30 28 32 35 (25) () GVF 400B~490B
2525M-352B 20 21 20 125 28 26 25 GVF 200BR
2020K-501B 25 26 25 150 30 28 32 5.1 GVF 250B~350B
2525M-501B GVF 150BR
2020K-502B 20 21 20 125 28 26 25 4.6 GVF 400B~490B
2525M-502B 25 25 150 30 28 32 50 GVF 200BR
2020K-701B 20 26 8.0 20 125 28 26 25 50 70 GVF 250B~350B
2525M-701B 25 21 25 150 30 28 32 5.1 (25) () GVF 150BR
2020K-702B GVF 400B~490B
2525M-702B 26 GVF 200BR
2525M-501C GVF 350C~450C
2525M-502C 20 21 20 125 28 26 25 4.6 70 100 GVF 500C~600C
2525M-701C 25 26 25 150 30 28 32 70 (25) ( ) GVF 350C~450C
2525M-702C 20 21 20 125 28 26 25 GVF 500C~600C
2525M-1001C 25 26 25 150 30 28 32 5.1 GVF 350C~450C
2525M-1002C GVF 500C~600C
2525M-1501C 6.6 50 50 70 GVF 350C~450C
2525M-1502C 8.1 (25) () GVF 500C~600C
33
35 6.6 70 70 100
8.1 (25) ()
25 26 9.5 25 150 35 32
6.6 100 150
8.1 100 (25) ()
6.6 150 150 250
8.1 (25) ()
Note1. Dimension T shows available grooving depth.
2. D1 shows toolholder head diameter to L3.
3. The value ( ) of Face Grooving Dia. (D Max) is the maximum outer diameter value after the initial groove between MIN~MAX. (It is possible to widen the groove to infinity ).
The value ( ) of Face Grooving Dia. (D Min) is the minimum diameter of the boss which remains in the center when widening the groove width to a smaller value after the initial
groove between MIN~MAX.
4. Standard toolholders are designed with the edge position 1.0mm above the center. When using non-standard Toolholders, set the Edge position 1.0mm above the center.
Selection of Toolholder & Insert
Toolholder R-hand Toolholder L-hand
Insert R-hand Insert L-hand
: Std. Item : Check Availability
G78 для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru