Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-to[oClse.rurmet / Coated Carbide / Carbide]
55°Diamond • Positive with Hole (mm)
Description A T d
DC_0702_ 6.35 2.38 2.8 11
DC_11T3_ 9.525 3.97 4.4 11
P Free-cutting steel B
Classication of usage
Positive
Carbon Steel and Alloy Steel : Interruption / 1st Choice Insert
M Stainless Steel
Ar : Interruption / 2nd Choice $
d Gray Cast Iron %
K : Light Interruption / 1st Choice 3
Nodular Cast Iron 4
:Light Interruption / 2nd Choice
N
Non-ferrous Metals :Continuous / 1st Choice
S Heat-resistant alloy : Continuous / 2nd Choice
55 T Titanium Alloy (In case hardness is under 45HRC)
Insert Description
H Hard Materials
Handed Insert
shows Left-hand PVD
Coated Carbide
Sharp Edge Dim. TN6010CermetPVD
Super Fine (mm) TN6020Cermet
Sharp Edge / Precision TN60
PV7005
With Honing PV7010
PV7020
CA5505
CA5515
CA5525
CA5535
CA6515
CA6525
CA4010
CA4115
CA4120
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
KW10 Carbide
Ref. Page for
Toolholder
CVD Coated Carbide
r Applicable
Chipbreaker Range
DCGT 11T3003F -J 0.03 5
11T301F -J 0.1 7
11T302F -J 0.2
Low Feed
DCGT 11T3005MF -J < 0.05 8
11T301MF -J < 0.1
11T302MF -J < 0.2 Insert (Turning)
11T304MF -J < 0.4
DCET 11T3003F -JSF 0.03 (mm) (Steel / Edge Length=11)
11T301F -JSF 0.1 4
Low Feed 11T302F -JSF 0.2 Refer to the table below
3 U / USF
DCET 11T3005MF -JSF < 0.05 ap ap
11T301MF -JSF < 0.1 2
11T302MF -JSF < 0.2 J / JSF
DCGT 11T3003E -J 0.03 1
11T301E -J 0.1 F / FSF
11T302E -J 0.2
11T304E -J 0.4 0.1 0.2 0.3 0.4
f (mm/rev)
Low Feed DCGT 11T3005ME -J < 0.05
11T301ME -J < 0.1
11T302ME -J < 0.2
11T304ME -J < 0.4
Non-ferrous Metals 0.4 (mm) (Non-ferrous Metals)
0.8 4
DCGT 11T304AH
11T308AH 3
AH
Non-ferrous Finishing-Medium / Sharp Edge DCGT 070202 -A3 0.2
R2
DCGT 11T302 -A3 0.2
11T304 -A3 0.4 A3
1
Finishing-Medium / Sharp Edge 0.1
0.2 0.1 0.2 0.3 0.4
DCGW 070201 f (mm/rev)
070202
Cast Iron DCGW 11T301 0.1
11T302 0.2
Without Chipbreaker 11T304 0.4
Insert whose corner R(r) dimension expressed with less than sign (e.g. <0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R(r).
Description Ref. Page for Toolholder
DC..07 type E14~17,E19~21,F29,F51~52
DC..11 type E14~17,E19~21,F29,F44,F51~52
For grades TN30 PV60 PR905 , See Page B75
PV30 PV90 PR915
B55Inserts are sold in 10 piece boxes.
: Std. Item : Check Availability R : Std. Item (R-hand Only) kyLo:cSetrda.@Itekmyo(Lc-ehraan-dtoOonlsly.)ru
www.kyocera-tools.ru