Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
Turning Indexable Inserts
55°Diamond • Positive with Hole (mm)
Description A T d
DP_0702_ 6.35 2.38 2.8 11
DP_11T3_ 9.525 3.97 4.4 11
B P Free-cutting steel
Classication of usage
Positive
Insert Carbon Steel and Alloy Steel : Interruption / 1st Choice
M Stainless Steel
$ Ar : Interruption / 2nd Choice
% d Gray Cast Iron
3 K : Light Interruption / 1st Choice
4 Nodular Cast Iron
5 :Light Interruption / 2nd Choice
7 N
8 Non-ferrous Metals :Continuous / 1st Choice
S Heat-resistant alloy : Continuous / 2nd Choice
55 T Titanium Alloy (In case hardness is under 45HRC)
Description
Insert H Hard Materials
Handed Insert PVD
shows Left-hand Coated Carbide
Dim. TN6010CermetPVD
Super Fine (mm) TN6020Cermet
TN60
PV7005
PV7010
PV7020
CA5505
CA5515
CA5525
CA5535
CA6515
CA6525
CA4010
CA4115
CA4120
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
KW10 Carbide
Ref. Page for
Toolholder
CVD Coated Carbide
r Applicable
Chipbreaker Range
DPET 0702003 -FSF 0.03 (mm) (Steel / Edge Length=07)
070201 -FSF 0.1 3
070202 -FSF 0.2 2 U / USF
ap
Insert (Turning) DPET 11T3003 -FSF 0.03 1
Finishing 11T301 -FSF 0.1 FSF
11T302 -FSF 0.2
0.1 0.2 0.3 0.4
DPET 0702005M -FSF < 0.05 f (mm/rev)
070201M -FSF < 0.1
070202M -FSF < 0.2 ap (mm) (Steel / Edge Length=11)
4
3 U / USF
2
J
1 F / FSF
DPET 11T3005M -FSF < 0.05
11T301M -FSF < 0.1
11T302M -FSF < 0.2 0.1 0.2 0.3 0.4
f (mm/rev)
Sharp Edge / Precision E16
Super Fine (mm) (Steel / Edge Length=07)
4
DPET 0702003F -USF 0.03
070201F -USF 0.1
070202F -USF 0.2 3
Low Feed DPET 11T3003F -USF 0.03 2
ap ap11T301F -USF 0.1
11T302F -USF 0.2 U / USF
1
F / FSF
0.1 0.2 0.3 0.4
f (mm/rev)
DPET 0702005MF -USF < 0.05 (mm) (Steel / Edge Length=11)
4
070201MF -USF < 0.1 3 U / USF
070202MF -USF < 0.2
2
J / JSF
DPET 11T3005MF -USF < 0.05 1
11T301MF -USF < 0.1 F / FSF
11T302MF -USF < 0.2
0.1 0.2 0.3 0.4
f (mm/rev)
Sharp Edge / Precision
Insert whose corner R(r) dimension expressed with less than sign (e.g. <0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R(r).
For grades TN30 PV60 PR905 , See Page B75
PV30 PV90 PR915
Inserts are sold in 10 piece boxes.
B56 : Std. Item : Check Availability R : Std. Item (R-hand Only) kyLo:cSetrda.@Itekmyo(Lc-ehraan-dtoOonlsly.)ru
www.kyocera-tools.ru