Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
Turning Indexable Inserts
55°Diamond • Positive with Hole (mm)
Description A T d
DC_0702_ 6.35 2.38 2.8 7
DC_11T3_ 9.525 3.97 4.4 7
B P Free-cutting steel
Classication of usage
Positive Ar
Insert d Carbon Steel and Alloy Steel : Interruption / 1st Choice
M Stainless Steel
$ : Interruption / 2nd Choice
% Gray Cast Iron
3 K : Light Interruption / 1st Choice
4 Nodular Cast Iron
5 :Light Interruption / 2nd Choice
7 N
8 Non-ferrous Metals :Continuous / 1st Choice
55 T S Heat-resistant alloy : Continuous / 2nd Choice
Description
Insert Titanium Alloy (In case hardness is under 45HRC)
Handed Insert H Hard Materials
shows Left-hand
PVD
Coated Carbide
Dim. TN6010CermetPVD
(mm) TN6020Cermet
TN60
PV7005
PV7010
PV7020
CA5505
CA5515
CA5525
CA5535
CA6515
CA6525
CA4010
CA4115
CA4120
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
KW10 Carbide
Ref. Page for
Toolholder
CVD Coated Carbide
r Applicable
Chipbreaker Range
DCGT 0702003F -U 0.03
070201F -U 0.1
070202F -U 0.2
Insert (Turning) DCGT 11T3003F -U 0.03
Low Feed 11T301F -U 0.1
11T302F -U 0.2
DCGT 0702003MF -U < 0.03
0702005MF -U < 0.05
070201MF -U < 0.1 (mm) (Steel / Edge Length=07)
070202MF -U < 0.2 4
070204MF -U < 0.4
DCGT 11T3005MF -U < 0.05 3
11T301MF -U < 0.1
Sharp Edge 11T302MF -U < 0.2 Refer to the table below 2
Super Fine 11T304MF -U < 0.4 U / USF
ap ap
DCET 0702003F -USF 0.03 1
070201F -USF 0.1 F / FSF
070202F -USF 0.2
0.1 0.2 0.3 0.4
Low Feed DCET 11T3003F -USF 0.03 f (mm/rev)
11T301F -USF 0.1
11T302F -USF 0.2 (mm) (Steel / Edge Length=11)
4
DCET 0702005MF -USF < 0.05 3 U / USF
070201MF -USF < 0.1
070202MF -USF < 0.2 2
J / JSF
Sharp Edge / Precision DCET 11T3005MF -USF < 0.05
11T301MF -USF < 0.1 1
11T302MF -USF < 0.2 F / FSF
DCGT 070201E -U 0.1 0.1 0.2 0.3 0.4
070202E -U 0.2 f (mm/rev)
070204E -U 0.4
Low Feed DCGT 11T301E -U 0.1
11T302E -U 0.2
11T304E -U 0.4
DCGT 070201ME -U < 0.1
070202ME -U < 0.2
070204ME -U < 0.4
With Honing DCGT 11T301ME -U < 0.1
11T302ME -U < 0.2
11T304ME -U < 0.4
Insert whose corner R(r) dimension expressed with less than sign (e.g. <0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R(r).
Description Ref. Page for Toolholder
DC..07 type E14~17,E19~21,F29,F51~52
DC..11 type E14~17,E19~21,F29,F44,F51~52
For grades TN30 PV60 PR905 , See Page B75
PV30 PV90 PR915
Inserts are sold in 10 piece boxes.
B54 : Std. Item : Check Availability R : Std. Item (R-hand Only) kyLo:cSetrda.@Itekmyo(Lc-ehraan-dtoOonlsly.)ru
www.kyocera-tools.ru