Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-to[oClse.rurmet / Coated Carbide / Carbide]
55°Diamond • Positive with Hole (mm)
Description A T d
DC_0702_ 6.35 2.38 2.8 7
DC_11T3_ 9.525 3.97 4.4 7
Free-cutting steel B
P Classication of usage
Carbon Steel and Alloy Steel : Interruption / 1st Choice Positive
Ar M Stainless Steel Insert
d : Interruption / 2nd Choice
Gray Cast Iron $
K : Light Interruption / 1st Choice %
Nodular Cast Iron 3
:Light Interruption / 2nd Choice 4
N 5
Non-ferrous Metals :Continuous / 1st Choice 7
Heat-resistant alloy 8
55 T S Titanium Alloy : Continuous / 2nd Choice
Description Hard Materials (In case hardness is under 45HRC)
Insert H
Handed Insert PVD
shows Left-hand Coated Carbide
Dim. TN6010CermetPVD
(mm) TN6020Cermet
TN60
PV7005
PV7010
PV7020
CA5505
CA5515
CA5525
CA5535
CA6515
CA6525
CA4010
CA4115
CA4120
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
KW10 Carbide
Ref. Page for
Toolholder
CVD Coated Carbide
r Applicable
Chipbreaker Range
DCGT 0702003 -F 0.03
070201 -F 0.1
070202 -F 0.2
070204 -F 0.4
DCGT 11T3003 -F 0.03
11T301 -F 0.1
Finishing 11T302 -F 0.2 Insert (Turning)
11T304 -F 0.4
DCGT 0702005M -F < 0.05
070201M -F < 0.1
070202M -F < 0.2
070204M -F < 0.4
DCGT 11T3005M -F < 0.05
11T301M -F < 0.1
11T302M -F < 0.2 Refer to the table below (mm) (Steel / Edge Length=07,11)
11T304M -F < 0.4 3
ap
Super Fine DCET 0702003 -FSF 0.03 2
070201 -FSF 0.1
070202 -FSF 0.2 F / FSF
070204 -FSF 0.4 1 (07)
DCET 11T3003 -FSF 0.03 F / FSF
11T301 -FSF 0.1 (11)
Finishing 11T302 -FSF 0.2
11T304 -FSF 0.4 0.1 0.2 0.3 0.4
f (mm/rev)
DCET 0702005M -FSF < 0.05
070201M -FSF < 0.1
070202M -FSF < 0.2
070204M -FSF < 0.4
DCET 11T3005M -FSF < 0.05
11T301M -FSF < 0.1
Sharp Edge / Precision 11T302M -FSF < 0.2
11T304M -FSF < 0.4
DCGT 070202 -FS 0.2
070204 -FS 0.4
Finishing / Medium DCGT 11T302 -FS 0.2
11T304 -FS 0.4
11T308 -FS 0.8
Insert whose corner R(r) dimension expressed with less than sign (e.g. <0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R(r).
Description Ref. Page for Toolholder
DC..07 type E14~17,E19~21,F29,F51~52
DC..11 type E14~17,E19~21,F29,F44,F51~52
For grades TN30 PV60 PR905 , See Page B75
PV30 PV90 PR915
B53Inserts are sold in 10 piece boxes.
: Std. Item : Check Availability R : Std. Item (R-hand Only) kyLo:cSetrda.@Itekmyo(Lc-ehraan-dtoOonlsly.)ru
www.kyocera-tools.ru