Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Turning Indexable Inserts
55°Rhombic / Positive with Hole Description A (mm)
T d
DC_0702_ 6.35 2.38 2.8 7
DC_11T3_ 9.525 3.97 4.4 7
B P Free-Cutting Steel
Classification of usage
Positive Ar M
Insert d Carbon steel / Alloy steel
K : Interruption / 1st Choice
$
% N Stainless Steel
3 : Interruption / 2nd Choice
4 55 T S
5 Description Gray Cast Iron
7 Insert H : Light Interruption / 1st Choice
8
Handed insert Dim. Cermet MEGACOAT CVD Coated PVD Coated MEGACOAT Carbide Nodular Cast IronRef. Page for
shows L-Hand (mm) Cermet Carbide Carbide : Light Interruption / 2nd ChoiceToolholder
r TN6010TN6020TN60PV7005PV7010PV7025CA5505CA5515CA5525CA5535CA6515CA6525CA4505CA4515PR930PR1005PR1025PR1125PR1225PR1305PR1310PR1325KW10 Non-ferrous Metals
SW05 : Continuous / 1st Choice
Heat-Resistant Alloys
: Continuous / 2nd Choice
Titanium Alloy
(In case hardness is under 45HRC)
Hard materials
Applicable
Chipbreaker Range
(ap indicates radius)
DCGT 0702003F -U 0.03
070201F -U 0.1
070202F -U 0.2
Insert (Turning) DCGT 11T3003F -U 0.03
Low Feed 11T301F -U 0.1
11T302F -U 0.2
DCGT 0702003MF -U < 0.03 (mm) (Steel / Edge Length=07)
0702005MF -U < 0.05 4
070201MF -U < 0.1
070202MF -U < 0.2 3
070204MF -U < 0.4
Sharp Edge Refer to the table below 2
Super Fine DCGT 11T3005MF -U < 0.05 U / USF
11T301MF -U < 0.1 ap ap
11T302MF -U < 0.2 1
11T304MF -U < 0.4 F / FSF
DCET 0702003F -USF 0.03 0.1 0.2 0.3 0.4
070201F -USF 0.1 f (mm/rev)
070202F -USF 0.2
Low Feed (mm) (Steel / Edge Length=11)
DCET 11T3003F -USF 0.03 4 U / USF
11T301F -USF 0.1
11T302F -USF 0.2 3
DCET 0702005MF -USF < 0.05
070201MF -USF < 0.1
070202MF -USF < 0.2
Sharp Edge / Precision DCET 11T3005MF -USF < 0.05 2
11T301MF -USF < 0.1 J / JSF
11T302MF -USF < 0.2
1
DCGT 070201E -U 0.1 F / FSF
070202E -U 0.2
070204E -U 0.4 0.1 0.2 0.3 0.4
f (mm/rev)
Low Feed DCGT 11T301E -U 0.1
11T302E -U 0.2
11T304E -U 0.4
DCGT 070201ME -U < 0.1
070202ME -U < 0.2
070204ME -U < 0.4
With Honing DCGT 11T301ME -U < 0.1
11T302ME -U < 0.2
11T304ME -U < 0.4
Insert whose corner R (r) dimension expressed with less than sign (e.g.<0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R (r).
Insert Description Ref. Page for Toolholder
DC..07type
DC..11type E22~25,E34,F35~39
E22~25,E34,F35~39,F66
TN30 PV30 PV60 PV90 PV7020 Reference Page B58
CA4010 CA4115 CA4120 PR915 PR905
Inserts are sold in 10 piece boxes.
B56
: Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) : Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru