Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
[Cermet / Coated Carbide / Carbide]
55°Rhombic / Positive with Hole (mm)
Description A T d
DC_0702_ 6.35 2.38 2.8 7
DC_11T3_ 9.525 3.97 4.4 7
P Q Free-Cutting Steel B
M PQ Classification of usage
K PP P Carbon steel / Alloy steel Positive
N Q T: Interruption / 1st Choice Insert
Ar Stainless Steel
55 T S d S: Interruption / 2nd Choice C
S Gray Cast Iron D
H Q: Light Interruption / 1st Choice R
Nodular Cast Iron S
P: Light Interruption / 2nd Choice T
Q Non-ferrous Metals V
W
N: Continuous / 1st Choice
Heat-Resistant Alloys
O: Continuous / 2nd Choice
Q Titanium Alloy
(In case hardness is under 45HRC)
Hard materials
Dim. TN6010CermetMEGACOATCVD CoatedPVD Coated MEGACOAT Applicable
(mm) TN6020Cermet Carbide Carbide Chipbreaker Range
Insert Description TN60 (ap indicates radius)
PV7005
Handed insert r PV7010
shows L-Hand PV7025
CA5505
CA5515
CA5525
CA5535
CA6515
CA6525
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
PR1225
PR1305
PR1310
PR1325
KW10 Carbide
SW05
Ref. Page for
Toolholder
DCGT 070202&-FS 0.2 N
070204&-FS 0.4 N
Finishing / Medium DCGT 11T302&-FS 0.2 N
11T304&-FS 0.4 N
11T308&-FS 0.8 N UN Insert (Turning)
NN
DCGT 0702003&-F 0.03 U NN
070201&-F 0.1 N NN
070202&-F 0.2 N
070204&-F 0.4
Finishing DCGT 11T3003&-F 0.03 N N R
11T301&-F 0.1 N N N
11T302&-F 0.2 N N N
11T304&-F 0.4 N N
DCGT 0702005M&-F < 0.05 NN N Refer to the table below (mm) (Steel / Edge Length=07,11)
070201M&-F < 0.1 UN N 3
070202M&-F < 0.2 UN N ap
070204M&-F < 0.4 UN N 2
DCGT 11T3005M&-F < 0.05 UU N F / FSF
11T301M&-F < 0.1 UN N 1 07
11T302M&-F < 0.2 NN N
11T304M&-F < 0.4 NN N F / FSF
11
Super Fine DCET 0702003&-FSF 0.03 N
070201&-FSF 0.1 N 0.1 0.2 0.3 0.4
070202&-FSF 0.2 N
070204&-FSF 0.4 N f (mm/rev)
U
N
N
Finishing DCET 11T3003&-FSF 0.03 N N
11T301&-FSF 0.1 N N
11T302&-FSF 0.2 N N
11T304&-FSF 0.4 N
DCET 0702005M&-FSF < 0.05 UN
070201M&-FSF < 0.1 NN
070202M&-FSF < 0.2 NN
070204M&-FSF < 0.4 NN
Sharp Edge / Precision DCET 11T3005M&-FSF < 0.05 UN
11T301M&-FSF < 0.1 NN
11T302M&-FSF < 0.2 NN
11T304M&-FSF < 0.4 NN
Insert whose corner R (r) dimension expressed with less than sign (e.g.<0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R (r).
Insert Description Ref. Page for Toolholder
DC..07type E22~25,E34,F35~39
DC..11type E22~25,E34,F35~39,F66
TN30
CA4010
PV30 PV60 PV90 PV7020 Reference Page B58
CA4115 CA4120 PR915 PR905
Inserts are sold in 10 piece boxes. B55
: Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) : Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru