Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
[Cermet / Coated Carbide / Carbide]
55°Rhombic / Positive with Hole Description A (mm)
T d
DC_0702_ 6.35 2.38 2.8 7
DC_11T3_ 9.525 3.97 4.4 7
P Free-Cutting Steel B
Classification of usage
Ar M Positive
d Carbon steel / Alloy steel Insert
K : Interruption / 1st Choice
$
N Stainless Steel %
: Interruption / 2nd Choice 3
55 T S 4
Insert Description Gray Cast Iron
H : Light Interruption / 1st Choice
Handed insert
shows L-Hand Nodular Cast Iron
: Light Interruption / 2nd Choice
Sharp Edge
Super Fine Non-ferrous Metals
: Continuous / 1st Choice
Sharp Edge / Precision
Heat-Resistant Alloys
With Honing : Continuous / 2nd Choice
Titanium Alloy
(In case hardness is under 45HRC)
Hard materials
Dim. Cermet MEGACOAT CVD Coated PVD Coated MEGACOAT Carbide Ref. Page for
(mm) Cermet Carbide Carbide Toolholder
Applicable
r TN6010 TN6020 TN60 PV7005 PV7010 PV7025 CA5505 CA5515 CA5525 CA5535 CA6515 CA6525 CA4505 CA4515 PR930 PR1005 PR1025 PR1125 PR1225 PR1305 PR1310 PR1325 KW10 Chipbreaker Range
SW05
(ap indicates radius)
DCGT 11T3003F -J 0.03 5
11T301F -J 0.1 7
11T302F -J 0.2
Low Feed
DCGT 11T3005MF -J < 0.05 8
11T301MF -J < 0.1
11T302MF -J < 0.2 (mm) Insert (Turning)
11T304MF -J < 0.4 4
DCET 11T3003F -JSF 0.03 3 (Steel / Edge Length=11)
11T301F -JSF 0.1 U / USF
11T302F -JSF 0.2
Low Feed Refer to the table below
DCET 11T3005MF -JSF < 0.05 2
11T301MF -JSF < 0.1 ap ap J / JSF
11T302MF -JSF < 0.2
1
DCGT 11T3003E -J 0.03 F / FSF
11T301E -J 0.1
11T302E -J 0.2 0.1 0.2 0.3 0.4
11T304E -J 0.4 f (mm/rev)
Low Feed DCGT 11T3005ME -J < 0.05
11T301ME -J < 0.1
11T302ME -J < 0.2
11T304ME -J < 0.4
Non-ferrous Metals DCGT 11T304AH 0.4 (mm) (Non-ferrous Metals)
11T308AH 0.8 4
Non-ferrous Metals Finishing-Medium / Sharp Edge 0.2 3
AH
DCGT 070202 -A3
2
A3
1
DCGT 11T302 -A3 0.2 0.1 0.2 0.3 0.4
11T304 -A3 0.4 f (mm/rev)
Finishing-Medium / Sharp Edge
DCGW 070201 0.1
070202 0.2
Cast Iron DCGW 11T301 0.1
11T302 0.2
Without Chipbreaker 11T304 0.4
Insert whose corner R (r) dimension expressed with less than sign (e.g.<0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R (r).
Insert Description Ref. Page for Toolholder
DC..07type E22~25,E34,F35~39
DC..11type E22~25,E34,F35~39,F66
Inserts are sold in 10 piece boxes. B57
: Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) : Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru