Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
[Cermet / Coated Carbide / Carbide]
(mm)
80°Rhombic / Positive with Hole (mm) Description A T d
Description A T d CC_0602_ 6.35 2.38 2.8 7
CC_0301_ 3.5 1.4 1.9 7 CC_09T3_ 9.525 3.97 4.4 7
CC_0401_ 4.3 1.8 2.3 7 CC_1204_ 12.7 4.76 5.5 7
r PQ Free-Cutting Steel Classification of usage B
NO Q PQP Carbon steel / Alloy steel T: Interruption / 1st Choice
Stainless Steel S: Interruption / 2nd Choice Positive
M PPQ Gray Cast Iron Q: Light Interruption / 1st Choice Insert
Nodular Cast Iron P: Light Interruption / 2nd Choice
A d KS Non-ferrous Metals N: Continuous / 1st Choice C
Heat-Resistant Alloys O: Continuous / 2nd Choice D
NQ Titanium Alloy (In case hardness is under 45HRC) R
Hard materials S
80 T S Q T
Description V
H W
Dim. Cermet MEGACOAT CVD PVD MEGACOAT Carbide Ref. Page for Applicable
(mm) Cermet Coated Carbide Coated Carbide Toolholder Chipbreaker Range
Insert r TN6010TN6020TN60 PV7005PV7010PV7025CA5505CA5515CA5525CA5535CA6515CA6525CA4505CA4515PR930PR1005PR1025PR1125PR1225PR1305PR1310PR1325KW10 (ap indicates radius)
SW05
Handed insert
Cast Iron shows L-Hand CCGW 060200 0.0 N E20~21
060201 0.1 N F27~29
Without Chipbreaker 060202 0.2 N
Super Fine N E20~21
CCGW 09T300 0.0 N F27
Sharp Edge / Precision 09T301 0.1 N F66
09T302 0.2 N Insert (Turning)
Sharp Edge 09T304 0.4
N
CCET 0301003&-FSF 0.03 L N N
030101&-FSF 0.1 N N N
030102&-FSF 0.2 N N N
030104&-FSF 0.4 N N
N
Finishing CCET 0401003&-FSF 0.03 L N
040101&-FSF 0.1 N N
040102&-FSF 0.2 L N
040104&-FSF 0.4 N
N (mm)
CCET 0301005M&-FSF < 0.05 N N (Steel / Edge Length=03)
030101M&-FSF < 0.1 N N
030102M&-FSF < 0.2 N N 0.5
030104M&-FSF < 0.4 N N F / FSF
N
CCET 0401005M&-FSF < 0.05 N N F27~ 0
040101M&-FSF < 0.1 N N F29 0.05 0.1 0.15 0.2
040102M&-FSF < 0.2 N ap f (mm/rev)
040104M&-FSF < 0.4 N N
N (mm)
CCGT 0301003&-F 0.03 L L N N ap (Steel / Edge Length=04)
030101&-F 0.1 N LN N N
030102&-F 0.2 L L N LN N N 0.5
030104&-F 0.4 L L N N N F / FSF
L N
CCGT 0401003&-F 0.03 LN N N 0
040101&-F 0.1 N LN N 0.05 0.1 0.15 0.2
040102&-F 0.2 L L N N f (mm/rev)
040104&-F 0.4 L L N N
Finishing
CCGT 0301005M&-F < 0.05 UN
030101M&-F < 0.1 UN
030102M&-F < 0.2 LN
030104M&-F < 0.4 LN
CCGT 0401005M&-F < 0.05 UN
040101M&-F < 0.1 UN
040102M&-F < 0.2 NN
040104M&-F < 0.4 NN
Finishing-Medium CCGT 060202&-FS 0.2 N E20~21
060204&-FS 0.4 N U F27~29
N N E20~21
N N F27
CCGT 09T302&-FS 0.2 N
09T304&-FS 0.4 F66
09T308&-FS 0.8
Insert whose corner R(r) dimension expressed with less than sign (e.g.<0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R (r).
TN30
CA4010
PV30 PV60 PV90 PV7020 Reference Page B49
CA4115 CA4120 PR915 PR905
B47Inserts are sold in 10 piece boxes.
: Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) : Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru