Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Turning Indexable Inserts
80°Rhombic / Positive with Hole Description A T d Description A T d
CC_0301_ 3.5 1.4 1.9 7 CC_0602_ 6.35 2.38 2.8 7
CC_0401_ 4.3 1.8 2.3 7 CC_09T3_ 9.525 3.97 4.4 7
CC_1204_ 12.7 4.76 5.5 7
B rA d P Free-Cutting Steel Classification of usage
T M Carbon steel / Alloy steel : Interruption / 1st Choice
Positive 80 K Stainless Steel : Interruption / 2nd Choice
Insert N Gray Cast Iron : Light Interruption / 1st Choice
S Nodular Cast Iron : Light Interruption / 2nd Choice
$ H Non-ferrous Metals : Continuous / 1st Choice
% Heat-Resistant Alloys : Continuous / 2nd Choice
3 Titanium Alloy
4 Hard materials (In case hardness is under 45HRC)
5
7 Dim. Cermet MEGACOAT CVD PVD MEGACOAT Carbide Ref. Page for
8 (mm) Cermet Coated Carbide Coated Carbide
Toolholder Applicable
Insert Description TN6010TN6020TN60PV7005PV7010PV7025CA5505CA5515CA5525CA5535CA6515CA6525CA4505CA4515PR930PR1005PR1025PR1125PR1225PR1305PR1310PR1325KW10 Chipbreaker Range
SW05
Handed insert r (ap indicates radius)
shows L-Hand
Insert (Turning) CCGT 0602003F -U 0.03 E20~21
Low Feed 060201F -U 0.1 F27~29
060202F -U 0.2
E20~21
CCGT 09T3003F -U 0.03 F27
09T301F -U 0.1 F66
09T302F -U 0.2
CCGT 0602005MF -U < 0.05 E20~21
060201MF -U < 0.1 F27~29
060202MF -U < 0.2
060204MF -U < 0.4
Sharp Edge CCGT 09T3005MF -U < 0.05 E20~21 ap ap (mm)
Super Fine 09T301MF -U < 0.1 F27 (Steel / Edge Length=06)
09T302MF -U < 0.2 F66
Sharp Edge / Precision 09T304MF -U < 0.4 3
E20~21
CCET 0602003F -USF 0.03 F27~29 2
060201F -USF 0.1 U / USF
060202F -USF 0.2 E20~21
F27 1
Low Feed CCET 09T3003F -USF 0.03 F66
09T301F -USF 0.1 0.1 0.2 0.3 0.4
09T302F -USF 0.2 E20~21 f (mm/rev)
F27~29
CCET 0602005MF -USF < 0.05 (mm) (Steel / Edge Length=09)
060201MF -USF < 0.1 E20~21 4
060202MF -USF < 0.2 F27
F66 3
CCET 09T3005MF -USF < 0.05 U / USF
09T301MF -USF < 0.1 E20~21
09T302MF -USF < 0.2 F27~29 2
CCGT 060201E -U 0.1 E20~21 1
060202E -U 0.2 F27
060204E -U 0.4 F66 0.1 0.2 0.3 0.4
f (mm/rev)
Low Feed CCGT 09T301E -U 0.1
09T302E -U 0.2
09T304E -U 0.4
CCGT 060201ME -U < 0.1 E20~21
060202ME -U < 0.2 F27~29
060204ME -U < 0.4
With Honing CCGT 09T301ME -U < 0.1 E20~21
09T302ME -U < 0.2 F27
09T304ME -U < 0.4 F66
Insert whose corner R(r) dimension expressed with less than sign (e.g.<0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R (r).
TN30 PV30 PV60 PV90 PV7020 Reference Page B49
CA4010 CA4115 CA4120 PR915 PR905
Inserts are sold in 10 piece boxes.
B48
: Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) : Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru