Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Turnin8g0In°dexableInserts (mm)
80°Rhombic / Positive with Hole (mm) Description A T d
Description A T d CC_0602_ 6.35 2.38 2.8 7
CC_0301_ 3.5 1.4 1.9 7 CC_09T3_ 9.525 3.97 4.4 7
CC_0401_ 4.3 1.8 2.3 7 CC_1204_ 12.7 4.76 5.5 7
B P Q Free-Cutting Steel Classification of usage
O T: Interruption / 1st Choice
Positive r QONT PQP Carbon steel / Alloy steel S: Interruption / 2nd Choice
Insert T M Q: Light Interruption / 1st Choice
K S NQ P PPQ Stainless Steel P: Light Interruption / 2nd Choice
C Description N P N: Continuous / 1st Choice
D d S NT S Gray Cast Iron O: Continuous / 2nd Choice
R H (In case hardness is under 45HRC)
S A NT Nodular Cast Iron
T
V Q Non-ferrous Metals
W
80 OP P NQT Heat-Resistant Alloys
P Q Titanium Alloy
Hard materials
Dim. Cermet MEGACOAT CVD PVD MEGACOAT Carbide Ref. Page for Applicable
(mm) Cermet Coated Carbide Coated Carbide Toolholder Chipbreaker Range
Insert r TN6010TN6020TN60PV7005PV7010PV7025CA5505CA5515CA5525CA5535CA6515CA6525CA4505CA4515PR930PR1005PR1025PR1125PR1225PR1305PR1310PR1325KW10 (ap indicates radius)
SW05
Handed insert
Insert (Turning) shows L-Hand CCGT 060201 0.1 N N N N E20~21
Medium 060202 0.2 N N N N F27~29
Sharp Edge 060204 0.4 N N N N
Finishing-Medium 0.1 N N E20~21
CCGT 09T301 0.2 N N N N F27
09T302 0.4 N N N N F66
09T304 N N
E20~21
CCMT 09T308 0.8 N N NNNN NNNNN NN F27~29
CCGT 0602005M < 0.05 N E20~21 ap (mm) (Steel / Edge Length=09)
060201M < 0.1 N F27 4
060202M < 0.2 N F66 Standard
060204M < 0.4 N 3
E20~21 GK
CCGT 09T3005M < 0.05 N F27~29 2
09T301M < 0.1 N
09T302M < 0.2 N E20~21 1 HQ
09T304M < 0.4 N F27
F66 0.1 0.2 0.3 0.4
CCGT 0602005MF < 0.05 N E20~21
Medium 060201MF < 0.1 NN N F27-29
060202MF < 0.2 NN N
060204MF < 0.4 NN N
N
CCGT 09T3005MF < 0.05 N
09T301MF < 0.1 NN N
09T302MF < 0.2 NN N
09T304MF < 0.4 NN N
0.2 N
CCGT 060202FN-Z 0.4 N
Medium Cutting 060204FN-Z 0.2 NN N
0.4 NN
CCGT 09T302FN-Z 0.8 N
09T304FN-Z NN N
09T308FN-Z NN N
Stainless Steel () (Stainless Steel)
2
CCMT 09T304MQ 0.4 NN N NNN N E20~21 ap 1 MQ
09T308MQ 0.8 NN N NNN N F27
ap
F66 0.1 0.2 0.3 0.4
f (mm/rev)
Non-ferrous Metals CCGT 09T304AH 0.4 N (mm) (Non-ferrous Metals)
09T308AH 0.8 4
N
3
Finishing-Medium / Sharp Edge AH
CCGT 09T302&-A3 0.2 N2
Non-ferrous Metals 09T304&-A3 0.4 A3
09T308&-A3 0.8 N 1
N
CCGT 120402&-A3 0.2 N 0.1 0.2 0.3 0.4
120404&-A3 0.4 N E21 f (mm/rev)
120408&-A3 0.8 N
Finishing-Medium / Sharp Edge
Insert whose corner R(r) dimension expressed with less than sign (e.g.<0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R (r).
TN30
CA4010
PV30 PV60 PV90 PV7020 Reference Page B49
CA4115 CA4120 PR915 PR905
Inserts are sold in 10 piece boxes.
B46 : Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru