Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
American National Tapered Pipe: NPT
External Thread Internal Thread
Nominal Thread TPI Toolholder Insert Toolholder Insert
Partial Prole Full Prole Partial Prole Full Prole
NPT 27 KTTR -16 TT32R6000 - No Tools Available
NPT KTTXR -16F TTX32R6000
NPT 18 KTNR -16 - 16ER18NPT PSH Sleeve HPTR06005-60-005 -
NPT KTNSR -16
(See J26) HPTR07507-60-005
NPT 14 KTNR -16 - 16ER14NPT PSH Sleeve HPTR07507-60-005 -
NPT KTNSR -16 (See J26)
NPT 14 KTNR -16 - 16ER14NPT No Tools Available
NPT KTNSR -16 SINR2016S-16
1 NPT - 16IR14NPT
1 NPT 16IR11.5NPT
SINR2420S-16
1 NPT
2 NPT KTNR -16 CINR3025S-16
KTNSR -16
11.5 - 16ER11.5NPT -
CINR3732S-16
Application of NPTF Thread J
NPTF is the thread for sealing pipes without using any sealing material.
Thread symbol is similar to NPT but the Tolerance is different from that of NPT, therefore the above Inserts are not available for NPTF.
30°Trapezoidal: Tr The JIS Standard Trapezoidal Size to be machined by TNN Insert are shown.
Pitch External Thread Internal Thread
(mm) Insert
Nominal Thread Toolholder Toolholder Insert Bore Threading
2 Partial Prole Dia.
Tr 16X2 Full Prole No Tools Available Partial Prole Full Prole 14.00
Tr 18X2 No Tools Available - No Tools Available 16.00
Tr 20X2 18.00
Tr 22X3 KTNR -16 16ER200TR SINR2016S-16 -- 19.00
Tr 24X3 KTNSR -16 21.00
Tr 26X3 23.00
3 - - 25.00
Tr 28X3 16IR300TR - 27.00
Tr 30X3 3 29.00
Tr 32X3
Tr 34X3 SINR2420S-16 16IR300TR - 31.00
Tr 36X3 33.00
Tr 38X3 3 CINR3025S-16 16IR300TR - 35.00
Tr 40X3 - 37.00
KTNR -16 16ER300TR
Tr 42X3 KTNSR -16 39.00
Tr 44X3 41.00
Tr 46X3 3 CINR3732S-16 16IR300TR - 43.00
Tr 48X3 45.00
Tr 50X3 47.00
Tr 52X3 49.00
Tr 55X3 52.00
Tr 60X3 57.00
Tr 65X3 62.00
Tr 70X4 4 KTNR -22 22ER400TR - CINR3732S-22 22IR400TR 66.00
Tr 75X4 71.00
Tr 80X4 76.00
Tr 90X4 86.00
Tr 95X4 -
Tr 100X4 91.00
Tr 105X4 96.00
Tr 110X4 101.00
106.00
TM Thread
TM Thread (old JIS 30°Trapezoidal Thread) has been discontinued. But if the “Nominal Dia. X Pitch” is the same, the above Tr Thread can be used.
TW Thread
TW Thread is 29°Trapezoidal Thread, therefore the above Inserts are not available.
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru J41