Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Applicable Toolholders & Inserts
The standard specication of the inch size thread is based on the dimension of 1/8 inch.
In Applicable Toolholder / Insert Lists on J40~J43, Right-hand Insert / Right-hand Toolholder descriptions are listed based on the previous TNN
type inserts. For other applicable inserts / toolholders or stock availability of Left-hand, see each relevant page and J46.
Parallel Pipe: G(PF), Rp(PS)
Nominal Thread External Thread (G) Internal Thread (G, Rp) Same
Symbol Root’s
TPI Toolholder Insert Toolholder Insert Bore Radius
(Previous Symbol) Dia.
Partial Prole Full Prole Partial Prole Full Prole
G
(-) 28 KTNR 16ERA55-TF - SINR0612S-06E - 6.56
KTNSR -16 16ERAG55-TF (HPT J24) 06IR5501 0.12
G
(PF ) -16 16ERA55 8.57
16ERAG55
G 19 KTNR -16 16ERA55-TF 16ER19W-TF SINR0816S-08E 08IR5501 - 11.45
(PF ) KTNSR -16 16ERAG55-TF 16ER19W (HPT J24) 0.18
16ERA55 16ER19W-TS
G 16ERAG55 SINR1216S-11E 11IRA55 - 14.95
(PF ) (HPT J24) 11IR55005
G SINR1516S-11 11IR55005 - 18.63
(PF )
G 14 KTNR -16 16ERAG55-TF 16ER14W-TF SINR2016S-16 16IRAG55 16IR14W-TF 20.59 0.25
(PF ) KTNSR -16 16ERG55-TF 16ER14W SINR2420S-16 16IRG55 16IR14W 24.12
16ERAG55 16ER14W-TS 16IR5501 16IR14W-TS
G 16ERG55 16IR5502
(PF )
27.88
G
J (PF )
G1 11 KTNR -16 16ERAG55-TF 16ER11W-TF SINR2420S-16 16IRAG55 16IR11W-TF 30.29
(PF 1) KTNSR -16 16ERG55-TF 16ER11W CINR3025S-16 16IRG55 16IR11W 34.94 0.32
16ERAG55 16ER11W-TS CINR3732S-16 16IR5501 16IR11W-TS 38.95
Threading G1 16ERG55 16IR5502
(PF 1 )
G1
(PF 1 )
Hereafter, all the threads are 11 TPI and the root’s radius 0.32.
The same tool for G1 is recommended.
Tapered Pipe: R, Rc(PT)(BSPT)
Nominal Thread External Thread (G) Internal Thread (G, Rp) Same
Root’s
Symbol TPI Toolholder Insert Toolholder Insert Radius
(Previous Symbol) 0.12
Partial Prole Full Prole Partial Prole Full Prole
0.18
R , Rc 28 KTNR -16 16ERA55-TF 16ER28BSPT-TF SINR0612S-06E 06IR5501 -
(-) KTNSR -16 16ERAG55-TF 16ER28BSPT (HPT J24) 0.25
16ERA55
R , Rc 16ERAG55 0.32
(PT )
R , Rc 19 KTNR -16 16ERA55-TF 16ER19BSPT-TF SINR0816S-08E -
(PT ) KTNSR -16 16ERAG55-TF 16ER19BSPT (HPT J24) 08IR5501
16ERA55 16ER19BSPT-TS 11IR19BSPT-TF
R , Rc 16ERAG55 SINR1216S-11E 11IRA55 11IR19BSPT
(PT ) (HPT J24) 11IRA55005 11IR19BSPT-TS
R , Rc 16ERAG55-TF 16ER14BSPT-TF SINR1516S-11 11IR55005 11IR14BSPT-TF
(PT ) 16ERG55-TF 16ER14BSPT SINR2016S-16 11IR14BSPT-TS
14 KTNR -16 16ERAG55 16ER14BSPT-TS
R , Rc KTNSR -16 16ERG55 16IR14BSPT-TF
(PT ) 16IR14BSPT
16IR14BSPT-TS
R 1, Rc 1
(PT 1) 11 KTNR -16 16ERAG55-TF 16ER11BSPT-TF SINR2420S-16 16IRAG55 16IR11BSPT-TF
KTNSR -16 16ERG55-TF 16ER11BSPT CINR3025S-16 16IRG55 16IR11BSPT
R 1 , Rc 1 16ERAG55 16ER11BSPT-TS CINR3732S-16 16IR5501 16IR11BSPT-TS
(PT 1 ) 16ERG55 16IR5502
R 1 , Rc 1
(PT 1 )
Hereafter, all the threads are 11 TPI and the root’s Hereafter, all the threads are 11 TPI and the root’s
radius 0.32. The same tool for R1 is recommended. radius 0.32. The same tool for Rc1 is recommended.
1) The largest size of minimum diameter holder is recommended for internal threading holders.
Therefore it is available if minimum diameter is smaller than recommended holders.
(ex.) SINR2420S-16 (Min. Bore Dia.: 24mm) is recommended for the Tool of G7/8 Internal Threading from the above Table, but
SINR2016S-16 can also be used.
2) When using “Partial Prole” for Tapered Pipe threading, thread’s corners become sharp edged, and the shape will not be the same as the standard shape for Tapered Pipe.
J40 для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru