Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Turnin8g0In°dexableInserts
mm mm
55°Rhombic / Negative with Hole Description A T d Description A T d
DN_1104_ 9.525 4.76 3.81 DN_1506_ 12.70 6.35 5.16
DN_1504_ 12.70 4.76 5.16
B P Free-cutting steel
O Classification of usage
Negative NQONT Carbon Steel / Alloy Steel
C M T: Interruption / 1st Choice
D K S NQ P Stainless Steel
R N P S: Interruption / 2nd Choice
S S Gray Cast Iron
A H Q: Light Interruption / 1st Choice
d Nodular Cast Iron
P: Light Interruption / 2nd Choice
TN6010 Non-ferrous Metals
TN6020 N: Continuous / 1st Choice
T OP P NQT Heat-resistant alloy
TN60
55 PV7005Description Q Titanium Alloy O: Continuous / 2nd Choice
PV7010
Insert PV7025 Hard Materials (In case hardness is under 45HRC)
CA5505
CA5515Dim.CermetMEGACOATCVDCoatedCarbidePVDMEGACOATCarbide
CA5525(mm)CermetCoated Carbide
CA5535 Applicable
CA6515r Chipbreaker Range
CA6525
CA4505 (ap indicates radius)
CA4515
PR930
PR1005
PR1025
PR1125
PR1225
PR1305
PR1310
PR1325
KW10
SW05
Ref. Page for
Toolholder
TInsert (Turning) DNMG 150404XP 0.4 N N N N N N N
Stainless Steel Stainless Steel / Heat-Resistant Alloys Stainless Steel / Heat-Resistant Alloys Stainless Steel / Heat-Resistant Alloys Stainless Steel / Heat-Resistant Alloys Stainless Steel Stainless Steel Low Carbon Steel Low Carbon Steel Low Carbon Steel Low Carbon SteelV 150408XP 0.8 N N N N N N N
DNMG 150604XP 0.4 N N
W Finishing 150608XP 0.8 N N (mm)
5
Low Carbon Steel
DNMG 150404XP-T 0.4 N 4
150408XP-T 0.8 N
ap 3
Finishing / Tough Edge DNMG 150404XQ 0.4 N N N N N N XQ XS
Medium 150408XQ 0.8 N N N N N N 2 XP
0.4 N N 1 XP-T
DNMG 150604XQ 0.8 N N N N
150608XQ 0.1 0.2 0.3 0.4 0.5
f (mm/rev)
DNMG 150408XS 0.8 N N N N
Roughing DNMG 150608XS 0.8 NN
DNMG 150404GU
0.4 NN
150408GU 0.8 NN
NN
Finishing DNMG 150604GU 0.4 NN
150608GU 0.8 N NN
D10 (mm)
DNMG 150408HU 0.8 N F11 5
150412HU 1.2 F65
NN
DNMG 150608HU 0.8 NN N NNN N Stainless Steel
150612HU 1.2 NN N NNN N
Medium-Roughing NN 4
DNMG 150404MQ 0.4 NN N NNN N HU
150408MQ 0.8 NN N NNN N ap ap
NN 3
0.4 NN N NNN N
Finishing-Medium DNMG 150604MQ 0.8 NN N NNN N 2 MU
Medium-Roughing 150608MQ 0.4 NN N NNN N MS
0.8 NN N NNN 1
DNMG 150404MS 1.2 NN N NNN GU
150408MS 0.4 NN N NNN
150412MS 0.8 NN 0.1 0.2 0.3 0.4 0.5
1.2 N NNN N f (mm/rev)
DNMG 150604MS 0.4 NN N NNN N
150608MS 0.8 NN (mm) Stainless Steel
150612MS N NNN N 5 TK
0.4 NN N NNN N 4
DNMG 150404MU 0.8 NN 3 MU
150408MU NN N
0.4 NN N
Medium-Roughing DNMG 150604MU 0.8 2
150608MU NN N
0.4 NN N 1
DNGG 150404TK 0.8 MQ MS
150408TK
0.4 0.1 0.2 0.3 0.4 0.5
DNGG 150604TK 0.8 f (mm/rev)
150608TK
Medium-Roughing / Sharp Edge 0.4
0.8
DNMG 150404TK N NNN Heat-Resistant Alloys
150408TK N NNN Titanium Alloys
Applicable Chipbreaker Range
Medium-Roughing DNMG 150604TK N NNN
150608TK N NNN See B7
DNMG 150604&-ST 0.4 N See B6
150608&-ST 0.8 NN
Medium-Roughing
B22 : Std. Item R : Std. Item (R-hand Only) Lд:лSяtdз.аIкteаmза(L--hkaynodceOrnal@y)kyoc:eCrhae-tcokoAlsv.ariulabilitwy ww.kyocera-tools.ru Inserts are sold in 10 piece boxes.