Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-toColes.rrumet / Coated Carbide / Carbide
mm mm
55°Rhombic / Negative with Hole Description A T d Description A T d
DN_1104_ 9.525 4.76 3.81 DN_1506_ 12.70 6.35 5.16
DN_1504_ 12.70 4.76 5.16
P Free-cutting steel B
O Classification of usage
O P Carbon Steel / Alloy Steel Negative
M P T: Interruption / 1st Choice C
KN S NT Stainless Steel D
P NT S: Interruption / 2nd Choice R
N S Gray Cast Iron S
A Q: Light Interruption / 1st Choice T
d S Nodular Cast Iron V
T Non-ferrous Metals P: Light Interruption / 2nd Choice W
TN6010H N: Continuous / 1st Choice
TN6020 Heat-resistant alloy
T O: Continuous / 2nd Choice
55 TN60Description T Titanium Alloy
PV7005 (In case hardness is under 45HRC)
Insert PV7010 Hard Materials
PV7025
Handed Insert CA5505Dim.CermetMEGACOATCVDCoatedCarbidePVDMEGACOATCarbide
shows R-hand CA5515(mm)CermetCoated Carbide
CA5525 Applicable
CA5535r Chipbreaker Range
CA6515
CA6525 (ap indicates radius)
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
PR1225
PR1305
PR1310
PR1325
KW10
SW05
Ref. Page for
Toolholder
Cast Iron DNMG 150404C 0.4 NN
150408C 0.8 NN
150412C 1.2
N
Roughing DNMG 150604C 0.4 NN (mm) Cast Iron Insert (Turning)
Roughing 150608C 0.8 NN 10
Roughing 150612C 1.2
Cast Iron Without Chipbreaker N ap 8 ZS
DNMG 150408ZS 0.8 GC
150412ZS 1.2 NN
NN 6
DNMG 150608ZS 0.8
150612ZS 1.2 NN 4
NN
Cast Iron DNMG 150408GC 0.8 2
150412GC 1.2 NN
N C (Standard)
DNMG 150608GC 0.8
150612GC 1.2 NN 0.2 0.4 0.6 0.8 1.0
N f (mm/rev)
DNMA 150404 0.4
Cast Iron 150408 0.8 NN N D10
NN N F11
DNMA 150604 0.4
150608 0.8 NN F65
NN
Non-ferrous Metals Non-ferrous Metals Non-ferrous Metals DNGG 150404&-A3 0.4 N
150408&-A3 0.8 N (mm)
5 Non-ferrous Metals
Finishing-Medium / Sharp Edge 0.4 4 ap ap AH
0.8
DNGG 150404AH N
150408AH 0.4 N3
0.8
DNGG 150604AH 2
150608AH 0.4
Medium-Roughing / Sharp Edge 0.8
1 A3
0.4
DNMG 150404AH 0.8 N 0.1 0.2 0.3 0.4 0.5
N f (mm/rev)
150408AH
DNMG 150604AH N
N
Medium-Roughing / With Honing 150608AH
Finishing DNGG 110402&-S 0.2 N (mm) Steel
110404&-S 0.4 N
110408&-S 0.8 N N5
Surface Roughness Oriented 0.4 N N D11 4
0.8 R N 3
DNGG 110404& F69
110408& 0.4 N N N
Medium 0.8 N N N N2
DNGG 150404& N 1S
150408&
N N D10 0.1 0.2 0.3 0.4 0.5
N N D11 f (mm/rev)
F65
See B44
Medium-Roughing
D 10
D 11
DNGG 150404FP-TK 0.4 N F6 5
150408FP-TK 0.8 N
Sharp Edge / Polished
TN30 PV30 PV60
CA4010 CA4115 CA4120
PV90 PV7020 Reference Page B24
PR915 PR905
B23Inserts are sold in 10 piece boxes.
: Std. Item R : Std. Item (R-hand Only) Lд:лSяtdз.аIкteаmза(L--hkaynodceOrnal@y)kyoc:eCrhae-tcokoAlsv.ariulabilitwy ww.kyocera-tools.ru