Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
[Cermet / Coated Carbide / Carbide]
55°Rhombic / Negative with Hole Description A T (mm) Description A T (mm)
DN_1104_ 9.525 4.76 d DN_1506_ 12.70 6.35 d
DN_1504_ 12.70 4.76 3.81 5.16
5.16
P Free-cutting steel Classification of usage B
Carbon Steel / Alloy Steel : Interruption / 1st Choice Negative
$
M Stainless Steel : Interruption / 2nd Choice %
3
Gray Cast Iron 4
A K : Light Interruption / 1st Choice
d Nodular Cast Iron
: Light Interruption / 2nd Choice
TN6010N Non-ferrous Metals
TN6020 Heat-resistant alloy : Continuous / 1st Choice
T S : Continuous / 2nd Choice
TN60 Titanium Alloy
55 PV7005Description (In case hardness is under 45HRC)
PV7010H Hard Materials
Insert PV7025
CA5505Dim.MEGACOAT PVD
CA5515(mm)CermetCoated Carbide
CA5525
CA5535
CA6515
CA6525
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
PR1225
PR1305
PR1310
PR1325
KW10
SW05
Ref. Page for
Toolholder
Cermet CVD MEGACOAT Carbide
Coated Carbide
Applicable
r Chipbreaker Range
(ap indicates radius)
Medium-Roughing DNMG 110404GS 0.4 D11 5
110408GS 0.8 F69 7
8
DNMG 150404GS 0.4 D10 See B20
150408GS 0.8 D11 Insert (Turning)
150412GS 1.2 F65
DNMG 150604GS 0.4
150608GS 0.8
150612GS 1.2
Medium-Roughing DNMG 150404PS 0.4
150408PS 0.8
150412PS 1.2
150416PS 1.6
Medium-Roughing / High Feed Medium-Roughing / High Feed Medium-Roughing / High Feed Medium-Roughing DNMG 150604PS 0.4 (mm) (Steel)
150608PS 0.8 GT
150612PS 1.2 5
150616PS 1.6 ap ap Standard
DNMG 150404HS 0.4 4
150408HS 0.8 PS(HS)
150412HS 1.2
3
DNMG 150604HS 0.4 2 PT
150608HS 0.8 1 GS
150612HS 1.2
0.1 0.2 0.3 0.4 0.5
DNMG 150408PT 0.8
150412PT 1.2 f (mm/rev)
DNMG 150608PT 0.8
150612PT 1.2
DNMG 150408GT 0.8 (mm) (Steel)
150412GT 1.2 10
DNMG 150608GT 0.8 D10 8 HX
150612GT 1.2 D11 6
F65 4
DNMG 150408HT 0.8 2 HT
150412HT 1.2
0.2 0.4 0.6 0.8 1.0
DNMG 150608HT 0.8
150612HT 1.2 f (mm/rev)
Roughing DNMG 150404 0.4
150408 0.8
150412 1.2
DNMG 150604 0.4
150608 0.8
150612 1.2
Roughing DNMG 150408PH 0.8 (mm) (Steel)
150412PH 1.2 10 PX
150416PH 1.6 ap
8
Single Sided \ Roughing / High Feed DNMG 150608PH 0.8 6 PH
150612PH 1.2 4
150616PH 1.6 2
DNMM 150408PX 0.8 0.2 0.4 0.6 0.8 1.0
150412PX 1.2
150416PX 1.6 f (mm/rev)
DNMM 150608PX 0.8
150612PX 1.2
150616PX 1.6
TN30 PV30 PV60 PV90 PV7020 Reference Page B24 Inserts are sold in 10 piece boxes.
CA4010 CA4115 CA4120 PR915 PR905
: Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) : Check Availability B21
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru