Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Turning Indexable Inserts
55°Rhombic / Negative with Hole Description A T (mm) Description A T (mm)
DN_1104_ 9.525 4.76 d DN_1506_ 12.70 6.35 d
DN_1504_ 12.70 4.76 3.81 CN_1906_ 19.05 6.35 5.16
5.16 7.94
B P Free-cutting steel Classification of usage
Negative Carbon Steel / Alloy Steel : Interruption / 1st Choice
$
% M Stainless Steel : Interruption / 2nd Choice
3
4 Gray Cast Iron
5 A K : Light Interruption / 1st Choice
7 d Nodular Cast Iron
8 : Light Interruption / 2nd Choice
TN6010N Non-ferrous Metals
TN6020 Heat-resistant alloy : Continuous / 1st Choice
T S : Continuous / 2nd Choice
TN60 Titanium Alloy
55 PV7005Description (In case hardness is under 45HRC)
PV7010H Hard Materials
Insert PV7025
CA5505Dim.MEGACOAT PVD
CA5515(mm)Cermet Coated Carbide
CA5525
CA5535
CA6515
CA6525
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
PR1225
PR1305
PR1310
PR1325
KW10
SW05
Ref. Page for
Toolholder
Cermet CVD MEGACOAT Carbide
Coated Carbide
Applicable
r Chipbreaker Range
(ap indicates radius)
Finishing DNGG 150404DP 0.4 D10
150408DP 0.8 D11
F65
Insert (Turning) Finishing DNMG 110404GP 0.4 D11 ap(mm) (Steel / Edge Length=11)
110408GP 0.8 F69 3
DNMG 150402GP 0.2 D10 2
150404GP 0.4 D11 HQ
150408GP 0.8 F65
1
DNMG 150602GP 0.2 GP
150604GP 0.4
150608GP 0.8 0.1 0.2 0.3 0.4 0.5
DNMG 110402HQ 0.2 f (mm/rev)
110404HQ 0.4
D11
DNMG 150404HQ 0.4 F69
150408HQ 0.8
Finishing-Medium 150412HQ 1.2 (mm)
0.4 (Steel / Edge Length=15)
DNMG 150604HQ 0.8
150608HQ 1.2 5
150612HQ
0.4 4 GP (Including DP)
DNMG 150404CQ 0.8
150408CQ 1.2 ap 3 CQ
150412CQ 2 HQ CJ
0.4
Finishing-Medium Finishing-Medium / Up Facing Finishing-Medium / Up Facing DNMG 150604CQ 0.8 1
150608CQ 1.2
150612CQ 0.1 0.2 0.3 0.4 0.5
0.8
DNMG 150408CJ 1.2 f (mm/rev)
150412CJ
0.8 D10 (mm) (Steel)
DNMG 150608CJ 1.2 D11 3 TN-V
150612CJ F65
0.4 2 HK
DNMP 150604TK 0.8
150608TK 1
Medium DNMG 150404HK 0.4 ap ap 0.1 0.2 0.3 0.4 0.5
150408HK 0.8
f (mm/rev)
(mm) (Steel)
5
Medium DNMG 150404TN-V 0.4 4
150408TN-V 0.8
3 CS
Medium-Roughing DNMG 150404CS 0.4 2
150408CS 0.8 GS
150604CS 0.4 1
DNMG 0.8
GS (11)
150608CS
0.1 0.2 0.3 0.4 0.5
f (mm/rev)
B20 Inserts are sold in 10 piece boxes.
: Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) : Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru