Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru Integral Type
Face Grooving Toolholders (Round Shank) [GVF Insert] Face Grooving Dia D1
(To outer dia.)
GIFV
A T D
F L2
Face Grooving Dia D1 H
(To outer dia.) L1
1
GIFVR3532B-201A GIFVL3532B-201A
shows Right Figure. shows Left Figure.
Right-hand Shown Left-hand Shown
R-hand Insert for R-hand Toolholder, L-hand Insert for L-hand Toolholder.
Toolholder Dimensions
G Std. Dimension (mm) Face Grooving Spare Parts
Dia. D1
Clamp Set Wrench
Applicable Inserts
Description
G83
R L A D H L1 L2 F T MIN. MAX.
GIFV 3532B-201A 35 23 2.2 35 CPS-5V - FT-15 - GVF 200A~340A
GIFV 3532B-351B (12) CPS-6V - LW-3 GVF 100AR~150AR
Grooving 3532B-352B CPS-8V LW-4 GVF 250B~350B
GIFV 5032B-501B 4.6 35 50 GVF 150BR
5032B-502B (25) () GVF 400B~490B
5032B-501C 35 GVF 200BR
5032B-502C 35 50 GVF 250B~350B
5.1 (25) () GVF 150BR
GVF 400B~490B
32 30 16 4.6 50 70 GVF 200BR
30 250 (25) ()
GVF 350C~450C
50 50 70 -
(25) () GVF 500C~600C
5.1
6.6 50 70
(25) ()
50 35
50 70
8.1 (25) ()
Dimension T shows available grooving depth.
2. Standard toolholders are designed with the edge position 1.0mm above the center.
Face Grooving Dia. D1 depends on the application.
Face Grooving Face Grooving Dia.
Dia. d1 D1
Application Description Remarks
(MIN.) MIN. MAX. (MAX.)
GIFV 3532B-201A
GIFV 3532B-351B 35 50
3532B-352B
d1 d1 D1 D1
D2 5032B-501B - -
GIFV 5032B-502B 50 70
5032B-501C
5032B-502C
GIFV 3532B-201A 12 If D2 58-2W, the Face Grooving Dia.
GIFV 3532B-351B 35 50 can be expanded to d1 (MIN.) towards
3532B-352B the Center. W = Edge Width
GIFV 5032B-501B 25 If D2 75-2W, the Face Grooving Dia.
5032B-502B 50 70 can be expanded to d1 (MIN.) towards
5032B-501C the Center. W = Edge Width
5032B-502C
GIFV 3532B-201A 12
GIFV 3532B-351B 35 50
3532B-352B
d1 D1
5032B-501B -
5032B-502B 25
GIFV 5032B-501C 50 70
5032B-502C
The value ( )of Face Grooving Dia. (D1 (Max)) is the maximum outer diameter value after the initial groove between MIN~MAX. (It is possible to widen the groove to infinity )
The value ( ) of Face Grooving Dia. (d1 (MIN)) is the minimum diameter of the boss which remains in the center when widening the groove width to a smaller value after the initial groove
between MIN~MAX.
: Std. Item : Check Availability
G88 для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru