Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Grooving / Cut-Off (Multi-Function)
GMM / GMN Classification of usage P Steel
M Stainless Steel
Cast Iron TN90
: Continuous-Light Interruption / 1st Choice K Non-ferrous Metals CR9025
: Continuous-Light Interruption / 2nd Choice N Titanium Alloy PR915
S Hard materials (under 40HRC) PR930
: Continuous / 1st Choice Hard materials (over 40HRC) KW10
: Continuous / 2nd Choice H Ref. Page for Toolholder
Dimension (mm) Angle Cermet CVD PVD Car-
° Ccoated Ccoated bide
Carbide Carbide
Insert Description
W r M L H
R-hand shown
GMM 1520-MT 1.5 0.0 1.2
0.05
W 0.05 r
22 2.0 0.0 1.5
2020-MT 0.05
M 20 4.3 -
HLr 0.0
2.5 0.05 1.9
2520-MT
Deep Grooving / Cut-Off 3020-MT 3.0 0.0 2.3
Sharp-Cutting Oriented 0.05
G GMM 1520 -MT-15D 1.5 0.0 1.2 15° R
0.05 R
Cut-Off W 0.05 R
Sharp-Cutting Oriented / 22 2020 -MT-15D 2.0 0.0 1.5 15° R
2520 -MT-15D 0.05 4.3
With lead angle M 20
H 15°
Deep Grooving / Cut-Off Lr 0.0
Sharp-Cutting Oriented 0.05
Without Chipbreaker 2.5 1.9
Grooving 3020 -MT-15D 3.0 0.0 2.3 15°
0.05
GMM 1520-NB 1.5 0.0 1.2
0.05
W 0.05 r
22 2.0 0.0 1.5
2020-NB 0.05
M 20 4.3 -
HLr 0.0
2.5 0.05 1.9
2520-NB
3020-NB 3.0 0.0 2.3
0.05
W 0.05 GMM 2020-TK 2.0 0.20 1.5 -
22 r 2520-TK 2.5 0.20 1.9 20 4.3
3.0 0.25 2.3
3020-TK
Deep Grooving / Cut-Off W 0.05 GMM 2020 -TK-8D 2.0 0.20 1.5 G36
Stability-Oriented 22 r 2520 -TK-8D 2.5 0.20 1.9 20 4.3 8°
G37
Cut-Off 3020 -TK-8D 3.0 0.25 2.3
Stability-Oriented / With lead angle R R R G38
RRRR
RRRR
GMN 2-TK 2.0 0.20 1.8 -
3.0 0.25 2.3 20 4.3
r 3-TK 4.0 0.30 3.3
4-TK
Cut-Off / Stability-oriented
1-Edge
GM 2-TK-8D 2.0 0.20 1.8 RRR
3.0 0.25 2.3 20 4.3 8° RRRR
r 3-TK-8D 4.0 0.30 3.3 RRRR
4-TK-8D
Cut-Off / Stability-oriented Shows GMN2.2 M 22 GMN 2.2 2.2 0.17 1.8
1-Edge / With lead angle Lr W 0.05 3 3.0 0.20 2.3
4 4.0 0.25 3.3 20 4.3 -
Deep Grooving / Cut-Off Shows GMR2.2-8D / 15D 5 5.0 0.8 4.2
1-Edge H 6 6.0 0.8 5.2
r
Cut-Off / Sharp-Cutting L 22 GM 2.2-8D 2.2 0.17 1.8 8° R R R
1-Edge / With lead angle W 0.05 2.2-15D RR
M 3-4D 2.2 0.00 1.8 15° R R
3-15D R
4-4D 3.0 0.20 2.3 20 4.3 4° R
R
3.0 0.20 2.3 15°
H 4.0 0.25 3.3 4°
For recommended cutting conditions, see page G93
G34 Inserts are sold : Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
in 10 piece boxes. для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru