Kyocera - Основной каталог 2011-2012 ENG

                                                      для заказа - kyocera@kyocera-tools.ru                                          CERACUT Plunge&Turn

GMN                                                   Classification of usage                       P  Carbon Steel / Alloy Steel    KBN10B
                                                                                                    M  Stainless Steel                       KBN510
                  Insert                              : Continuous-Light Interruption / 1st Choice  K  Cast Iron                                      KBN525
                                                      : Continuous-Light Interruption / 2nd Choice  N  Non-ferrous Metals                                     KPD001
                                                      : Continuous / 1st Choice                     S  Titanium Alloy                                                  KPD010
                                                      : Continuous / 2nd Choice                        Hard materials (under 40HRC)
                                                                                                    H  Hard materials (over 40HRC)                                          Ref. Page for Toolholder

                                                                        Dimension (mm)                              Angle            CBN               PCD
                                                                                                                     (°)

                                                      Description

                                                                   W r M L H 

                                                      GMN 2        2.0  0.2                         1.8
                                                              3         0.4
                                                              4
                                        SM22                  5    3.0  0.2                         2.3
                                 Lr           W 0.05          6         0.4
                         S=2.9
                                                                   4.0  0.2                         3.3  20    4.3  -                                       G37
                                                                        0.4                                                                                 G38

                                         H                              0.2
                                                                        0.4
                                                                   5.0                              4.2

Deep Grooving                                                      6.0  0.2                         5.2                                                                                               G
     1-Edge                                                             0.4

                                                                                                       For recommended cutting conditions, see page G91

Available cutting diameter of KGM                                                                      130
(For automatic lathe) / KGM-T type                                                                                        40 (D: Cutting Dia.)

   There is a limit to the possible grooving depth depending                                                                                                                            Grooving
   on the workpiece diameter.                                                                                       20 (t: Available Groove Depth)

                                                                                                                       If the workpiece diameter is large, the possible cutting
                                                                                                                       diameter becomes smaller due to interference with the tool-holder.

KGM Possible Cutting Diameter Table                                                                            e.g.) KGMR2525M-3T20+GMN3

     Toolholder                                                          D (Cutting Dia.)                              10 14 16 32
                                                                                                                60
KGM          0810K-1.5-125 - - - -                                         20 25 32 40                         100
             1010 -1.5                                             28 32 36 40 60
             1212 -1.5       ----                                                                                       10 14 16 32
                                                                           20 25 32 40                          60
                             ----                      25 26       28 50
                                                                                                                60
             0810K-2-125 - - - -                       25 26               20 25 32 40                         100
             1010  -2                                  80 100      28 32 36 40 60
             1212  -2         ----                                                                               65432
             1616  -2         ----                     25 26       11 10 9 8 7
             1010  -2.5      32 40 50 60               80 100
                              ----                     80 100
                                                      12.5 12
             1212 -2.5        ----
             1616 -2.5
             1616 -3         32 40 50 60
                             32 40 50 60

Available Grooving Depth t (mm) 16 15 14 13                                                                                                         1

KGM-T Possible Cutting Diameter Table (GMN, GM When using 1-edge insert)

     Toolholder                                                  D (Cutting Dia.)

KGM          2012K-2T17
             2020K-2T17
             2525M-2T17      -           -                                                          66 80 130  260
                                                                                                               14 Under 13
             1616H-3T20 -                -                       40 54 70 100 180
             2012K-3T20
             2020K-3T20
             2525M-3T20 -
             2020K-4T20                  -                       40 90 130 240

             2525M-4T20
             2525M-4T25
             2525M-5T25      -           - 50 140 240

             3232P-5T25 - - 50 280 600
             2525M-6T30 100 300

Available Grooving Depth t (mm) 30 27 25 23 22 20 19 18 17 16 15

: Std. Item    : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)                                                         CBN & PCD Inserts are
                                              для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru
                                                                                                                                                    G35sold in 1 piece boxes.