Kyocera - Основной каталог 2011-2012 ENG

                                                                                        для заказа - kyocera@kyocera-tools.ru

                  C5h5i°pDbiaremaoknedr/NSeegleactitvioen/w(iNthegHaotlieve Insert)

                                   Stainless Steel

                 Cutting                     Design                                       Advantages                             Cutting                    Design                Advantages
                           Name                                                                                                           Name
                                                                                                                                                                            0.15  Sharp cutting
B Range                                                                                                                          Range                                   20       performance
                                                                                                                                                                                  and low cutting
Insert (Turning)  Finishing                                                           23  Large rake                             Finishing        GU                          5   force due to
                                                                                          angle and                                                                               3-D rake angle.
                                   MQ                                                     circular edge                                                                           Applicable to
                                                                                      15  line.                                                                                   small shaft
                                                                                          Low cutting                                                                             cutting.
                                                                                          force and good
                                                                                          chip control.

                                                                                          Superior

                  Medium-Roughing                          0.25                                        cutting edge              Medium-Roughing            0.2                   Sharp cutting
                                                          12                                                                                                                  20  performance
                                                                                          19 sharpness                                                                            and strong
                                                                                                       and strength                                                       20      edge due to
                                                                                                                                                                                  3-D rake angle.
                                                                                          achieved by a                                                                           Applicable to
                                                                                                                                                                                  small shaft
                                   MS                     0.25                            positive land.                                          HU                              cutting.

                                                                                          19 Extra strength

                                                          9 of cutting edge

                                                                                          inhibits damage

                                                                                          from wall

                                                                                          shouldering.

                  Medium-Roughing                                                        Large rake                              Medium-Roughing                                           Less cutting
                                                          15 angle reduces                                                                                                                 force due to
                                                                                                                                                            14 large rake
                                                                                          cutting force.                                                                                   angle.
                                                                                                                                                                                           Less notching
                                   MU                                                     Less burring                                            ST                                       by special
                                                                                                                                                                                           design.
                                                                                          achieved by
                                                          15 diminishing

                                                                                          damage from

                                                                                          notching.

                                                                                                                                                  Applicable Chipbreaker Range

                  Medium-Roughing                                                                                 Smooth                              (mm)  (Stainless steel)
                                                                                                                                                        5
                                                                                   13 chipbreaker
                                                                                                                  geometry                                        HU
                                                                                                                                                      4 ST
                                                                                                                  improves chip
                                   TK ow with less

                                                                                    9 adhesion.

                                                                                                                  Large curled

                                                                                                                  chips.

                                                                                                                                                  ap  3

                                   Applicable Chipbreaker Range

                                       (mm)               (Stainless steel)                                                                           2

                                       5                                                                                                             1 GU
                                                      TK

                                   ap  4                                                                                                                    0.1 0.2 0.3 0.4 0.5
                                                                                                                                                                    f (mm/rev)
                                                                       MU
                                       3

                                       2

                                       1
                                                      MQ MS

                                                 0.1 0.2 0.3 0.4 0.5
                                                         f (mm/rev)

B6

                                                                                          для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru