Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
Turning Indexable Inserts
(mm) (mm)
60°Triangle • Positive with Hole Description A T d Description A T d
TP_0802_ 4.76 2.38 2.3 11 TP_1103_ 6.35 3.18 3.3 11
TP_0902 5.56 2.38 3.0 11 TP_1603_ 9.525 3.18 4.5 11
B TP_1102 6.35 2.38 3.5 11 TP_1604_ 9.525 4.76 4.4 11
Positive Free-cutting steel
Insert P Classication of usage
60 Carbon Steel and Alloy Steel : Interruption / 1st Choice
$
% M Stainless Steel : Interruption / 2nd Choice
3
4 K Gray Cast Iron : Light Interruption / 1st Choice
5 Nodular Cast Iron :Light Interruption / 2nd Choice
7
8 A N Non-ferrous Metals :Continuous / 1st Choice
d
r S Heat-resistant alloy : Continuous / 2nd Choice
T TN6010 Titanium Alloy (In case hardness is under 45HRC)
TN6020 Hard Materials
H
TN60
PV7005Dim.CermetPVD PVD
PV7010(mm)Cermet Coated Carbide
PV7020
CA5505
CA5515
CA5525
CA5535
CA6515
CA6525
CA4010
CA4115
CA4120
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
KW10 Carbide
Ref. Page for
Toolholder
CVD Coated Carbide
Insert Description r Applicable
Chipbreaker Range
Handed Insert TPGH 080201
shows Left-hand 080202
080204
Insert (Turning) 0.1 E22 ap(mm) (Steel / Edge Length=08,09)
TPGH 090201 0.2 F55 2
Finishing 090202 0.4 F58 1
090204 0.1 0.2 0.3 0.4
0.1 F33 ap f (mm/rev)
TPGH 110202 0.2 F55
110204 0.4 F58 (mm) (Steel / Edge Length=11,16)
3
TPGH 110302 0.2 F57 2 (11)
110304 0.4 (16)
110308 E22 1
0.2 F33 0.1 0.2 0.3 0.4
TPGH 160302 0.4 F55 f (mm/rev)
160304 0.8 F57
160308
0.2 F33
TPGH 080201M 0.4 F55
080202M 0.8 F57
080204M
< 0.1 E22
TPGH 090201M < 0.2 F55
090202M < 0.4 F58
090204M
< 0.1 F33
TPGH 110202M < 0.2 F55
110204M < 0.4 F58
TPGH 110302M < 0.2 F57
110304M < 0.4
110308M E22
< 0.2 F33
TPGH 160302M < 0.4 F55
160304M < 0.8 F57
160308M
< 0.2 F33
< 0.4 F55
< 0.8 F57
TPGH 110302 -H 0.2 E22
110304 -H 0.4 F33
110308 -H 0.8 F55
F57
Medium TPGH 160304 -H 0.4 (mm) (Steel / Edge Length=11,16)
ap160308 -H0.8F333
F55 H (16)
TPGT 160402 -H 0.2 F57 2
160404 -H 0.4
160408 -H 0.8 - 1
H (11)
TPGH 110302M -H < 0.2 E22
110304M -H < 0.4 F33 0.1 0.2 0.3 0.4
110308M -H < 0.8 F55 f (mm/rev)
F57
TPGH 160304M -H < 0.4 F33
160308M -H < 0.8 F55
F57
Insert whose corner R(r) dimension expressed with less than sign (e.g. <0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R(r).
For grades TN30 PV60 PR905 , See Page B76
PV30 PV90 PR915
Inserts are sold in 10 piece boxes.
B62 : Std. Item : Check Availability R : Std. Item (R-hand Only) kyLo:cSetrda.@Itekmyo(Lc-ehraan-dtoOonlsly.)ru
www.kyocera-tools.ru