Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-to[oClse.rurmet / Coated Carbide / Carbide]
(mm) (mm)
60°Triangle • Positive with Hole Description A T d Description A T d
TP_0802_ 4.76 2.38
TPMT0902_ 5.56 2.38 2.3 11 TP_1103_ 6.35 3.18 3.3 11
TP_0902 5.56 2.38
TP_1102 6.35 2.38 2.8 11 TPMT1603_ 9.525 3.18 4.4 11
CVD Coated Carbide 3.0 11 TP_1603_ 9.525 3.18 4.5 11 B
3.5 11 TP_1604_ 9.525 4.76 4.4 11 Positive
Insert
Free-cutting steel
P Classication of usage $
60 Carbon Steel and Alloy Steel : Interruption / 1st Choice %
r M Stainless Steel 3
:Interruption / 2nd Choice 4
Insert Gray Cast Iron 5
K Nodular Cast Iron :Light Interruption / 1st Choice
:Light Interruption / 2nd Choice
A d N
Non-ferrous Metals :Continuous / 1st Choice
Heat-resistant alloy
T S Titanium Alloy :Continuous / 2nd Choice
Description Hard Materials (In case hardness is under 45HRC)
H
Dim. Cermet PVD PVD KW10 Carbide
(mm) Cermet Coated Carbide Ref. Page for
r TN6010 Toolholder Applicable
TN6020 Chipbreaker Range
TN60
PV7005
PV7010
PV7020
CA5505
CA5515
CA5525
CA5535
CA6515
CA6525
CA4010
CA4115
CA4120
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
TPGT 080202CF 0.2 E22 7
F55 8
TPGT 090202CF 0.2 F58
(mm) (Steel / Edge Length=08,09)
Minute ap TPGT 080201M-CF < 0.1 F33 .3 Insert (Turning)
080202M-CF < 0.2 F55
F58 ap ap XP
Sharp Edge TPGT 090201M-CF < 0.1 (GP)
090202M-CF < 0.2 E22 0.2
F55
F58 0.1 CF
F33 0.05 0.1 0.15 0.2
F55 f (mm/rev)
F58
Minute ap TPGT 080201MP-CF < 0.1
080202MP-CF < 0.2 E22
F55
F58
TPGT 090201MP-CF < 0.1 F33 (mm) (Steel / Edge Length=08,09)
090202MP-CF < 0.2 F55 3
Sharp Edge / Polished Surface F58
0.2 2
TPMT 090202GP 0.4 E22 HQ
090204GP F33
F55 1
Finishing TPMT 110304GP 0.4 F57 XP
110308GP 0.8 F33 (GP)
F55 0.1 0.2 0.3 0.4
TPMT 160304GP 0.4 F57 f (mm/rev)
F33
Finishing-Medium TPMT 090202HQ 0.2 F55 ap ap (mm) (Steel / Edge Length=11)
TPMT 090204HQ 0.4 F58 3
XQ
TPMT 110302HQ 0.2 E22 2
110304HQ 0.4 F33 HQ
110308HQ 0.8 F55 1
F57 XP
160302HQ 0.2 (GP)
160304HQ 0.4 F33 0.1 0.2 0.3 0.4
160308HQ 0.8 F55 f (mm/rev)
F57
TPMT 090204XP 0.4
F33
Low Carbon Steel TPMT 110304XP 0.4 F55
110308XP 0.8 F58
E22
F33
F55
F57
TPMT 160304XP 0.4 F33 (mm) (Steel / Edge Length=16)
160308XP 0.8 F55 3
F57
Finishing TPMT 110304XQ 0.4 XQ
110308XQ 0.8 E22 2
Low Carbon Steel F33
F55 HQ
F57 1
XP
(GP)
TPMT 160304XQ 0.4 F33 0.1 0.2 0.3 0.4
160308XQ 0.8 F55 f (mm/rev)
F57
Finishing-Medium
Insert whose corner R(r) dimension expressed with less than sign (e.g. <0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R(r).
For grades TN30 PV60 PR905 , See Page B76
PV30 PV90 PR915
B61Inserts are sold in 10 piece boxes.
: Std. Item : Check Availability R : Std. Item (R-hand Only) kyLo:cSetrda.@Itekmyo(Lc-ehraan-dtoOonlsly.)ru
www.kyocera-tools.ru