Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
Turning Indexable Inserts (mm)
(mm) Description A T d
7
60°Triangle • Positive with Hole / Description A T d TC_0902_ 5.56 2.38 2.5 7
without Hole 7
TB_0601_ 3.97 1.59 2.3 5 TC_1102_ 6.35 2.38 2.8
TC_0802_ 4.76 2.38 2.3 7 TC_1103_ 6.35 3.18 2.8
B 60 P Free-cutting steel
Classication of usage
Positive Insert
Insert Carbon Steel and Alloy Steel : Interruption / 1st Choice
Handed Insert M Stainless Steel
$ shows Left-hand : Interruption / 2nd Choice
% Gray Cast Iron
3 K Nodular Cast Iron : Light Interruption / 1st Choice
4 :Light Interruption / 2nd Choice
5 A N
7 d Non-ferrous Metals :Continuous / 1st Choice
8 Heat-resistant alloy : Continuous / 2nd Choice
TN6010S Titanium Alloy
TN6020
T H Hard Materials (In case hardness is under 45HRC)
TN60
PV7005DescriptionDim.CermetPVDPVD
PV7010(mm)CermetCoated Carbide
PV7020
CA5505
CA5515
CA5525
CA5535
CA6515
CA6525
CA4010
CA4115
CA4120
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
KW10 Carbide
Ref. Page for
Toolholder
CVD Coated Carbide
r Applicable
Chipbreaker Range
TCGT 0802003F -U 0.03 E22
080201F -U 0.1
080202F -U 0.2
Insert (Turning) TCGT 1103003F -U 0.03 E22
Low Feed 110301F -U 0.1 F34
110302F -U 0.2
TCGT 0802005MF -U < 0.05 E22
080201MF -U < 0.1
080202MF -U < 0.2
TCGT 1103005MF -U < 0.05
110301MF -U < 0.1
110302MF -U < 0.2 E22
110304MF -U < 0.4 F34
Sharp Edge TCET 0802003F -USF 0.03 E22 (mm) (Steel / Edge Length=08,09,11)
Super Fine 080201F -USF 0.1 4
080202F -USF 0.2 E22
Sharp Edge / Precision F34 U (11)
TCET 1103003F -USF 0.03 ap 3
With Honing 110301F -USF 0.1
Low Feed 110302F -USF 0.2 U (08)
2
HQ
1
TCET 0802005MF -USF < 0.05 E22 0.1 0.2 0.3 0.4
080201MF -USF < 0.1 f (mm/rev)
080202MF -USF < 0.2 E22
F34
TCET 1103005MF -USF < 0.05
110301MF -USF < 0.1
110302MF -USF < 0.2
TCGT 080201E -U 0.1 E22
080202E -U 0.2
Low Feed TCGT 110301E -U 0.1 E22
110302E -U 0.2 F34
110304E -U 0.4
TCGT 080201ME -U < 0.1 E22
080202ME -U < 0.2
TCGT 110301ME -U < 0.1 E22
110302ME -U < 0.2 F34
110304ME -U < 0.4
Non-ferrous Metals TCGT 110302 -A3 0.2 E22 ap(mm) (Non-ferrous Metals)
110304 -A3 0.4 F34 2 A3
1 0.1 0.2 0.3 0.4
f (mm/rev)
Finishing-Medium / Sharp Edge
0.1 E22
TCGW 080201 0.2
Cast Iron 080202
TCGW 110301 0.1 E22
110302 0.2 F34
110304 0.4
Without Chipbreaker
Insert whose corner R(r) dimension expressed with less than sign (e.g. <0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R(r).
For grades TN30 PV60 PR905 , See Page B76
PV30 PV90 PR915
Inserts are sold in 10 piece boxes.
B60 : Std. Item : Check Availability R : Std. Item (R-hand Only) kyLo:cSetrda.@Itekmyo(Lc-ehraan-dtoOonlsly.)ru
www.kyocera-tools.ru