Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-to[oClse.rurmet / Coated Carbide / Carbide]
(mm)
(mm) Description A T d
7
60°Triangle • Positive with Hole Description A T d TC_1102_ 6.35 2.38 2.8
TB_0601_ 3.97 1.59
TC_0902_ 5.56 2.38 2.3 5 TC_1103_ 6.35 3.18 2.8 7
CVD Coated Carbide 2.5 7 TC_16T3_ 9.525 3.97 4.4 7
60 Free-cutting steel B
P Classication of usage
Insert Carbon Steel and Alloy Steel : Interruption / 1st Choice Positive
M Stainless Steel Insert
Handed Insert : Interruption / 2nd Choice
shows Left-hand Gray Cast Iron $
K Nodular Cast Iron : Light Interruption / 1st Choice %
:Light Interruption / 2nd Choice 3
A N 4
d Non-ferrous Metals :Continuous / 1st Choice 5
S Heat-resistant alloy : Continuous / 2nd Choice 7
TN6010 8
TN6020T Titanium Alloy (In case hardness is under 45HRC)
TN60DescriptionH Hard Materials
PV7005
PV7010Dim.CermetPVD PVD
PV7020(mm)Cermet Coated Carbide
CA5505
CA5515r Applicable
CA5525 Chipbreaker Range
CA5535
CA6515
CA6525
CA4010
CA4115
CA4120
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
KW10 Carbide
Ref. Page for
Toolholder
TBGT 060102CF 0.2
Minute ap TBGT 060101M-CF < 0.1 (mm) (Steel / Edge Length=06)
060102M-CF < 0.2 0.4
0.3
Sharp Edge
ap Insert (Turning)
Minute ap TBGT 060101MP-CF < 0.1 0.2
060102MP-CF < 0.2 0.1 CF
Sharp Edge / Polished Surface 0.05 0.1 0.15 0.2
f (mm/rev)
Finishing TBMT 060102DP 0.2 F33
060104DP 0.4 F55
F58
TBGT 0601003 0.03 (mm) (Steel / Edge Length=06)
060101 0.1 2
060102 0.2 ap
060104 0.4 1.5
Finishing
TBGT 0601005M < 0.05 1
060101M < 0.1 DP ( Without Indication)
060102M < 0.2
060104M < 0.4 0.5
0.05 0.1 0.15 0.2
f (mm/rev)
Cast Iron TBGW 060102 0.2 (mm) (Steel / Edge Length=08,09,11)
060104 0.4 4
Without Chipbreaker 0.2 ap U (11)
0.4 3
Finishing-Medium TCMT 090202HQ F34
090204HQ 0.2 U (08)
0.4 2
TCMT 110202HQ 0.8
110204HQ HQ
110208HQ 0.4 1
0.8
TCMT 16T304HQ 1.2 0.1 0.2 0.3 0.4
16T308HQ f (mm/rev)
16T312HQ
-
Finishing TCGT 110201 0.1 F34
110202 0.2
110204 0.4
Insert whose corner R(r) dimension expressed with less than sign (e.g. <0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R(r).
For grades TN30 PV60 PR905 , See Page B76
PV30 PV90 PR915
B59Inserts are sold in 10 piece boxes.
: Std. Item : Check Availability R : Std. Item (R-hand Only) kyLo:cSetrda.@Itekmyo(Lc-ehraan-dtoOonlsly.)ru
www.kyocera-tools.ru