Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-to[oClse.rurmet / Coated Carbide / Carbide]
55°Diamond • Positive with Hole (mm)
Description A T d
DC_0702_ 6.35 2.38 2.8 7
DC_11T3_ 9.525 3.97 4.4 7
P Free-cutting steel B
Classication of usage
Positive
Carbon Steel and Alloy Steel : Interruption / 1st Choice Insert
M Stainless Steel
Ar : Interruption / 2nd Choice $
d Gray Cast Iron %
K : Light Interruption / 1st Choice 3
Nodular Cast Iron 4
:Light Interruption / 2nd Choice
N
Non-ferrous Metals :Continuous / 1st Choice
Heat-resistant alloy : Continuous / 2nd Choice
T S Titanium Alloy
Description Hard Materials
55 H (In case hardness is under 45HRC)
Insert
PVD
Coated Carbide
Dim. TN6010CermetPVD
(mm) TN6020Cermet
TN60
PV7005
PV7010
PV7020
CA5505
CA5515
CA5525
CA5535
CA6515
CA6525
CA4010
CA4115
CA4120
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
KW10 Carbide
Ref. Page for
Toolholder
CVD Coated Carbide
r Applicable
Chipbreaker Range
Finishing-Medium DCGT 070201MF-GQ < 0.1 (mm) (Steel) 5
070202MF-GQ < 0.2 4 GK 7
070204MF-GQ < 04 8
3
Sharp Edge DCGT 11T301MF-GQ < 0.1 ap GQ Insert (Turning)
11T302MF-GQ < 0.2
Finishing-Medium 11T304MF-GQ < 0.4 2
DCGT 070201MFP-GQ < 0.1 1
070202MFP-GQ < 0.2 CK
070204MFP-GQ < 0.4
DCGT 11T301MFP-GQ < 0.1 0.1 0.2 0.3
11T302MFP-GQ < 0.2 f (mm/rev)
Sharp Edge / Polished Surface 11T304MFP-GQ < 0.4
(mm) (Steel / Edge Length=07)
DCMT 070202GK 0.2 3
070204GK 0.4 Standard
Finishing-Medium 070208GK 0.8 2
DCMT 11T302GK 0.2 Refer to the table below 1
11T304GK 0.4 HQ
11T308GK 0.8 ap ap
XP
Finishing-Medium DCMT 070202HQ 0.2 0.1 0.2 0.3 0.4
070204HQ 0.4
070208HQ 0.8 f (mm/rev)
DCMT 11T302HQ 0.2 (mm)
11T304HQ 0.4 (Steel / Edge Length=07,11)
11T308HQ 0.8
4
DCGT 070201 0.1
070202 0.2 3 Standard (11)
070204 0.4
2
DCGT 11T301 0.1 Conventional
11T302 0.2
11T304 0.4 1 Molded
(07)
Medium DCMT 11T308 0.8 0.1 0.2 0.3 0.4
f (mm/rev)
DCGT 0702005M < 0.05
070201M < 0.1 (mm)
070202M < 0.2 (Steel / Edge Length=11)
070204M < 0.4
4
DCGT 11T3005M < 0.05 3 Standard
11T301M < 0.1 2 HQ
11T302M < 0.2 ap
11T304M < 0.4
Medium DCGT 0702005MF < 0.05 1 XQ
DCGT 070201MF < 0.1 XP
070202MF < 0.2
070204MF < 0.4 0.1 0.2 0.3 0.4
f (mm/rev)
11T3005MF < 0.05
Sharp Edge 11T301MF < 0.1
11T302MF < 0.2
11T304MF < 0.4
Insert whose corner R(r) dimension expressed with less than sign (e.g. <0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R(r).
Description Ref. Page for Toolholder
DC..07 type E14~17,E19~21,F29,F51~52
DC..11 type E14~17,E19~21,F29,F44,F51~52
For grades TN30 PV60 PR905 , See Page B75
PV30 PV90 PR915
B51Inserts are sold in 10 piece boxes.
: Std. Item : Check Availability R : Std. Item (R-hand Only) kyLo:cSetrda.@Itekmyo(Lc-ehraan-dtoOonlsly.)ru
www.kyocera-tools.ru