Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru (mm)
Description A T d
Turning Indexable Inserts DC_0702_ 6.35 2.38 2.8 7
DC_11T3_ 9.525 3.97 4.4 7
55°Diamond • Positive with Hole
B P Free-cutting steel
Classication of usage
Positive Ar
Insert d Carbon Steel and Alloy Steel : Interruption / 1st Choice
M Stainless Steel
$ : Interruption / 2nd Choice
% Gray Cast Iron
3 K : Light Interruption / 1st Choice
4 Nodular Cast Iron
:Light Interruption / 2nd Choice
N
Non-ferrous Metals :Continuous / 1st Choice
S Heat-resistant alloy : Continuous / 2nd Choice
55 T Titanium Alloy (In case hardness is under 45HRC)
Insert Description
H Hard Materials
PVD
Coated Carbide
Dim. TN6010CermetPVD
(mm) TN6020Cermet
TN60
PV7005
PV7010
PV7020
CA5505
CA5515
CA5525
CA5535
CA6515
CA6525
CA4010
CA4115
CA4120
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
KW10 Carbide
Ref. Page for
Toolholder
CVD Coated Carbide
r Applicable
Chipbreaker Range
5 DCGT 070202CF 0.2
7 DCGT 11T302CF 0.2
DCGT 070201M-CF < 0.1Minute ap (mm) (Steel / Edge Length=07,11)
8 070202M-CF < 0.2 0.3
GP
Insert (Turning) Sharp Edge DCGT 11T301M-CF < 0.1 ap 0.2
11T302M-CF < 0.2
0.1 CF
DCGT 070201MP-CF < 0.1
Minute ap 070202MP-CF < 0.2
DCGT 11T301MP-CF < 0.1 0.05 0.1 0.15 0.2
11T302MP-CF < 0.2 f (mm/rev)
Sharp Edge / Polished Surface
070201MF-GF < 0.1
DCGT 070202MF-GF < 0.2
Finishing DCGT 11T301MF-GF < 0.1
11T302MF-GF < 0.2
11T304MF-GF < 0.4 (mm) (Steel)
3
Sharp Edge DCGT 070201MFP-GF < 0.1 Refer to the table below
070202MFP-GF < 0.2
ap 2 GQ
Finishing DCGT 11T301MFP-GF < 0.1 1 GF
11T302MFP-GF < 0.2 CF
Sharp Edge / Polished Surface 11T304MFP-GF < 0.4
0.05 0.1 0.15 0.2
DCGT 070201CK 0.1
070202CK 0.2 f (mm/rev)
Finishing DCGT 11T301CK 0.1
11T302CK 0.2
DCGT 070201M-CK < 0.1 (mm) (Steel)
070202M-CK < 0.2 4
DCGT 11T301M-CK < 0.1 ap 3
11T302M-CK < 0.2 GQ
2 GK
Finishing DCGT 070201MP-CK < 0.1 1
070202MP-CK < 0.2 CK
DCGT 11T301MP-CK < 0.1 0.1 0.2 0.3
11T302MP-CK < 0.2 f (mm/rev)
Sharp Edge / Polished Surface
070202GP 0.2
DCMT 070204GP 0.4
Finishing DCMT 11T304GP 0.4
11T308GP 0.8
Insert whose corner R(r) dimension expressed with less than sign (e.g. <0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R(r).
Description Ref. Page for Toolholder
DC..07 type E14~17,E19~21,F29,F51~52
DC..11 type E14~17,E19~21,F29,F44,F51~52
For grades TN30 PV60 PR905 , See Page B75
PV30 PV90 PR915
Inserts are sold in 10 piece boxes.
B50 : Std. Item : Check Availability R : Std. Item (R-hand Only) kyLo:cSetrda.@Itekmyo(Lc-ehraan-dtoOonlsly.)ru
www.kyocera-tools.ru