Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-to[oClse.rurmet / Coated Carbide / Carbide]
(mm)
(mm) Description A T d
80°Diamond • Positive with Hole Description A T d CC_0602_ 6.35 2.38 2.8 7
CC_0301_ 3.5 1.4 1.9 7 CC_09T3_ 9.525 3.97 4.4 7
CC_0401_ 4.3 1.8 2.3 7 CC_1204_ 12.7 4.76 5.5 7
P Free-cutting steel Classification of usage B
Carbon Steel and Alloy Steel : Interruption / 1st Choice
r M Stainless Steel Positive
T :Interruption / 2nd Choice Insert
Gray Cast Iron
Description K :Light Interruption / 1st Choice $
Cast Iron Nodular Cast Iron %
:Light Interruption / 2nd Choice 3
A N 4
d Non-ferrous Metals :Continuous / 1st Choice 5
S Heat-resistant alloy :Continuous / 2nd Choice 7
TN6010 8
TN602080 Titanium Alloy (In case hardness is under 45HRC)
TN60H Hard Materials
PV7005
PV7010Dim.CermetPVDCVD Coated Carbide PVD
PV7020(mm)Cermet Coated Carbide
CA5505
CA5515Insertr Applicable
CA5525 Chipbreaker Range
CA5535Handed Insert
CA6515shows Left-hand0.0 E11~13
CA65250.1 F24
CA4010Without Chipbreaker0.2 F49~50
CA4115Super Fine
CA4120 E11~13
CA4505 F24
CA4515 F44
PR930
PR1005
PR1025
PR1125
KW10 Carbide
Ref. Page for
Toolholder
CCGW 060200
060201
060202
CCGW 09T300 0.0 Insert (Turning)
09T301 0.1
09T302 0.2
09T304 0.4
CCET 0301003 -FSF 0.03
030101 -FSF 0.1
030102 -FSF 0.2
030104 -FSF 0.4
CCET 0401003 -FSF 0.03
040101 -FSF 0.1
Finishing 040102 -FSF 0.2
040104 -FSF 0.4
CCET 0301005M -FSF < 0.05
030101M -FSF < 0.1
030102M -FSF < 0.2
030104M -FSF < 0.4
CCET 0401005M -FSF < 0.05
040101M -FSF < 0.1
Sharp Edge / Precision 040102M -FSF < 0.2 F24 ap ap (mm)
040104M -FSF < 0.4 F49 (Steel / Edge Length=03)
CCGT 0301003 -F 0.03 0.5
030101 -F 0.1 F / FSF
030102 -F 0.2
030104 -F 0.4 0
0.05 0.1 0.15 0.2
f (mm/rev)
CCGT 0401003 -F 0.03 (mm) (Steel / Edge Length=04)
040101 -F 0.1 0.5
Finishing 040102 -F 0.2 F / FSF
040104 -F 0.4 0
0.05 0.1 0.15 0.2
f (mm/rev)
CCGT 0301005M -F < 0.05
030101M -F < 0.1
030102M -F < 0.2
030104M -F < 0.4
CCGT 0401005M -F < 0.05
040101M -F < 0.1
Sharp Edge 040102M -F < 0.2
040104M -F < 0.4
Finishing-Medium CCGT 060202 -FS 0.2 E11~13
060204 -FS 0.4
F24
F49~50
CCGT 09T302 -FS 0.2 E11~13
09T304 -FS 0.4 F24
09T308 -FS 0.8 F44
Insert whose corner R(r) dimension expressed with less than sign (e.g. <0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R(r).
For grades TN30 PV60 PR905 , See Page B74
PV30 PV90 PR915
B47Inserts are sold in 10 piece boxes.
: Std. Item : Check Availability R : Std. Item (R-hand Only) kyLo:cSetrda.@Itekmyo(Lc-ehraan-dtoOonlsly.)ru
www.kyocera-tools.ru