Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
Turning Indexable Inserts (mm)
(mm) Description A T d
80°Diamond • Positive with Hole Description A T d CC_0602_ 6.35 2.38 2.8 7
CC_0301_ 3.5 1.4 1.9 7 CC_09T3_ 9.525 3.97 4.4 7
CC_0401_ 4.3 1.8 2.3 7 CC_1204_ 12.7 4.76 5.5 7
B P Free-cutting steel Classification of usage
Carbon Steel and Alloy Steel : Interruption / 1st Choice
Positive r M Stainless Steel
Insert
Gray Cast Iron :Interruption / 2nd Choice
$
% A K Nodular Cast Iron :Light Interruption / 1st Choice
3 d
4 N :Light Interruption / 2nd Choice
5 TN6010
7 80 TN6020S Non-ferrous Metals :Continuous / 1st Choice
8 Heat-resistant alloy :Continuous / 2nd Choice
TN60
PV7005T Titanium Alloy (In case hardness is under 45HRC)
PV7010
PV7020H Hard Materials
CA5505
CA5515Dim.CermetPVD PVD
CA5525(mm)Cermet Coated Carbide
CA5535
CA6515
CA6525
CA4010
CA4115
CA4120
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
KW10 Carbide
Ref. Page for
Toolholder
CVD Coated Carbide
Insert Description r Applicable
Chipbreaker Range
Handed Insert CCGT 060201
shows Left-hand 060202
060204
0.1 E11~13
0.2 F24
0.4 F49~50
Insert (Turning) CCGT 09T301 0.1 E11~13
Medium 09T302 0.2 F24
09T304 0.4 F44
CCMT 09T308 0.8
CCGT 0602005M < 0.05 E11~13 (mm)
060201M < 0.1 F24 (Steel / Edge Length=09)
060202M < 0.2 F49~50
060204M < 0.4 4
E11~13 Standard
CCGT 09T3005M < 0.05 F24 ap
09T301M < 0.1 F44 3
09T302M < 0.2 GK
09T304M < 0.4
2
1 HQ
CCGT 0602005MF < 0.05 E11~13 0.1 0.2 0.3 0.4
060201MF < 0.1 f (mm/rev)
060202MF < 0.2 F24
Medium cutting 060204MF < 0.4 F49~50
CCGT 09T3005MF < 0.05 E11~13
09T301MF < 0.1 F24
Sharp Edge 09T302MF < 0.2 F44
09T304MF < 0.4
E11~13
Medium Cutting CCGT 060202FN-Z 0.2 F24
060204FN-Z 0.4 F49~50
CCGT 09T302FN-Z 0.2
09T304FN-Z 0.4
09T308FN-Z 0.8
Stainless Steel (mm) (Stainless Steel)
2
CCMT 09T304MQ 0.4 ap 1 MQ
09T308MQ 0.8 0.1 0.2 0.3 0.4
ap(mm)
Finishing-Medium E11~13 4 f (mm/rev)
F24
Non-ferrous Metals F44 (Non-ferrous Metals)
CCGT 09T304AH 0.4
09T308AH 0.8
Finishing-Medium / Sharp Edge 09T302 -A3 0.2 3
09T304 -A3 0.4
CCGT 09T308 -A3 0.8 AH
2
Non-ferrous Metals
A3
1
CCGT 120402 -A3 0.2 E12 0.1 0.2 0.3 0.4
120404 -A3 0.4 f (mm/rev)
Finishing-Medium / Sharp Edge 120408 -A3 0.8
Insert whose corner R(r) dimension expressed with less than sign (e.g. <0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R(r).
For grades TN30 PV60 PR905 , See Page B74
PV30 PV90 PR915
B46 : Std. Item Inserts are sold in 10 piece boxes.
: Check Availability R : Std. Item (R-hand Onlky)yocLe:rSat@d. kItyeomc(eLr-ah-atnodolOs.nrluy)
www.kyocera-tools.ru