Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
Turning Indexable Inserts (mm)
(mm) Description A T d
80°Diamond • Positive with Hole Description A T d CC_0602_ 6.35 2.38 2.8 7
CC_0301_ 3.5 1.4 1.9 7 CC_09T3_ 9.525 3.97 4.4 7
CC_0401_ 4.3 1.8 2.3 7 CC_1204_ 12.7 4.76 5.5 7
B P Free-cutting steel Classification of usage
Carbon Steel and Alloy Steel : Interruption / 1st Choice
Positive r
Insert
M Stainless Steel : Interruption / 2nd Choice
$
% Gray Cast Iron : Light Interruption / 1st Choice
3 A K
4 d Nodular Cast Iron
5 :Light Interruption / 2nd Choice
7 TN6010N
8 TN6020 Non-ferrous Metals :Continuous / 1st Choice
80 T S Heat-resistant alloy : Continuous / 2nd Choice
TN60
PV7005 Titanium Alloy (In case hardness is under 45HRC)
PV7010
PV7020H Hard Materials
CA5505
CA5515Dim.CermetPVDPVD
CA5525(mm)CermetCoated Carbide
CA5535
CA6515
CA6525
CA4010
CA4115
CA4120
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
KW10 Carbide
Ref. Page for
Toolholder
CVD Coated Carbide
Insert Description Applicable
Chipbreaker Range
Handed Insert r
shows Left-hand
CCGT 060200F -U 0.0 E11~13
0602003F -U 0.03 F24
060201F -U 0.1 F49~50
060202F -U 0.2
CCGT 09T300F -U 0.0 E11~13
09T3003F -U 0.03 F24
Insert (Turning) 09T301F -U 0.1 F44
Low Feed 09T302F -U 0.2
CCGT 0602005MF -U < 0.05 E11~13
060201MF -U < 0.1 F24
060202MF -U < 0.2 F49~50 (mm)
060204MF -U < 0.4 (Steel / Edge Length=06)
E11~13
CCGT 09T3005MF -U < 0.05 F24 3
09T301MF -U < 0.1 F44
Sharp Edge 09T302MF -U < 0.2 ap ap 2
Super Fine 09T304MF -U < 0.4 E11~13 U / USF
F24
CCET 0602003F -USF 0.03 F49~50 1
060201F -USF 0.1
060202F -USF 0.2 E11~13 0.1 0.2 0.3 0.4
F24 f (mm/rev)
Low Feed CCET 09T3003F -USF 0.03 F44
09T301F -USF 0.1 (mm) (Steel / Edge Length=09)
09T302F -USF 0.2 4
CCET 0602005MF -USF < 0.05 E11~13 3 U / USF
060201MF -USF < 0.1 F24 2
060202MF -USF < 0.2 F49~50
CCET 09T3005MF -USF < 0.05 E11~13 1
09T301MF -USF < 0.1 F24
Sharp Edge / Precision 09T302MF -USF < 0.2 F44
CCGT 060201E -U 0.1 E11~13 0.1 0.2 0.3 0.4
060202E -U 0.2 F24 f (mm/rev)
060204E -U 0.4 F49~50
Low Feed CCGT 09T301E -U 0.1 E11~13
09T302E -U 0.2 F24
09T304E -U 0.4 F44
CCGT 060201ME -U < 0.1 E11~13
060202ME -U < 0.2 F24
060204ME -U < 0.4 F49~50
With Honing CCGT 09T301ME -U < 0.1 E11~13
09T302ME -U < 0.2 F24
09T304ME -U < 0.4 F44
Insert whose corner R(r) dimension expressed with less than sign (e.g. <0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R(r).
For grades TN30 PV60 PR905 , See Page B74
PV30 PV90 PR915
Inserts are sold in 10 piece boxes.
B48 : Std. Item : Check Availability R : Std. Item (R-hand Only) kyLo:cSetrda.@Itekmyo(Lc-ehraan-dtoOonlsly.)ru
www.kyocera-tools.ru