Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
MRP Radius Mill
Cutting Performance of Radius Mill (Standard-type)
Workpiece Slotting
Material
D(Cutting Dia.) Cutting Conditions
Tooholder: Standard
$ Vc=120 ~ 150m/min (See below table)
4$
ap = varied fz= varied Dry
Overhang Length = L1 (See below table)
ap
Description
ap
ap
ap
.M3R1P012-4S16-08 .M3R1P016-4S16-08 .M3R1P020-4S20-08
On =3980NmJiOn-1 (7VDc =150NmN/mJOin
) On =2980NmJiOn-1 (7VDc =150NmN/mJOin
) On =2390NmJiOn-1 (7VDc =150NmN/mJOin
)
-L1 =42NmNm L-1 =42NmNm L-1 =42NmNm
5 ap (mm) 5 ap (mm) 5 ap (mm)
444
08 type
(RDMT08T2M0-H) 3 3 3
222
111
0.1 0.2 0.3 0.4 0.5 0.1 0.2 0.3 0.4 0.5 0.1 0.2 0.3 0.4 0.5
Feed Rate (mm/t
Feed Rate (mm/t
Feed Rate (mm/t
10 type .M3R1P025-4S25-10-35T .M3R1P032-4S32-10-45T
(RPMT10T3M0) On =1910NmJiOn-1 (7VDc =150NmN/mJOin
) On =1490NmJiOn-1 (7VDc =150NmN/mJOin
)
-L1 =60NmNm L-1 =80NmNm
6 ap (mm) 6 ap (mm)
5 5
4 4
3 3
2 2
Milling
ap ap
ap ap
ap
ap
0.1 0.2 0.3 0.4 0.5 0.1 0.2 0.3 0.4 0.5 .M3R1P040-4S32-12-45T .M3R1P050-4S42-12
Feed Rate (mm/t
On =1195NmJiOn-1 (7VDc =150NmN/mJOin
) On =765NmJiOn-1 (7VDc =120NmN/mJOin
)
M Feed Rate (mm/t
L-1 =80NmNm L-1 =80NmNm
.M3R1P032-4S25-12 .M3R1P040-4S32-12
On =1490NmJiOn-1 (7VDc =150NmN/mJOin
) On =1195NmJiOn-1 (7VDc =150NmN/mJOin
) 7 ap (mm) 7 ap (mm)
-L1 =80NmNm L-1 =80NmNm
6 6
7 ap (mm) 7 ap (mm)
5 5
12 type 6 6
(RPMT1204M0-H) 5 4 4
4 5
3 3
3 4
3
0.2 0.3 0.4 0.5 0.6 0.2 0.3 0.4 0.5 0.6 0.2 0.3 0.4 0.5 0.6 0.2 0.3 0.4 0.5 0.6
Feed Rate (mm/t
Feed Rate (mm/t
Feed Rate (mm/t
Feed Rate (mm/t
16 type .M3R1P040-4S32-16 .M3R1P050-4S42-16 .M3R1P063-4S42-16
(RPMT1606M0-H) On =1195NmJiOn-1 (7VDc =150NmN/mJOin
) On =765NmJiOn-1 (7VDc =120NmN/mJOin
) On =605NmJiOn-1 (7VDc =120NmN/mJOin
)
-L1 =90NmNm L-1 =90NmNm L-1 =90NmNm
8 ap (mm) 8 ap (mm) 6 ap (mm)
7 7 5
6 6 4
5 5 3
4 4 2
ap
ap
ap
0.2 0.3 0.4 0.5 0.6 0.2 0.3 0.4 0.5 0.6 0.2 0.3 0.4 0.5 0.6
Feed Rate (mm/t
Feed Rate (mm/t
Feed Rate (mm/t
M126 kyocera@kyocera-tools.ru
www.kyocera-tools.ru