Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
Applicable Inserts Applicable Inserts M16 Applicable Inserts M21
Toolholder
MEC····-11··· BDMT ER-JT BDMT ER-JS - -
1103 ER-JT 1103 ER-JS FR
MEC····-11T··· ER-JT ER-JS BDGT FR-JA BDMT FR
MEC··R-11··· BDMT BDMT 11T3 FR-JA 11T3
MEC····-17··· 11T3 11T3
MEC··R-17··· BDGT BDMT
BDMT BDMT 1704 1704
1704 1704
Recommended Cutting Conditions (MEC Endmill / Face Mill)
JT Chipbreaker Cutting Dia. 20~160
Cutting Dia. 10~18 MEC20~MEC40 MEC040R~MEC160R
MEC10~MEC18
Workpiece Recommended Insert Grade Workpiece Recommended Insert Grade
Material (Cutting Speed: m/min) Material (Cutting Speed: m/min)
fz (mm/t) PVD Coated Carbide fz (mm/t) PVD Coated Carbide
PR830 PR905 PR830 PR905
Stainless Steel 0.06~0.08~0.1 100~180 - Stainless Steel 0.08~0.12~0.15 100~180 -
Carbon Steel 0.06~0.1~0.15 120~200 - Carbon Steel 0.08~0.15~0.25 120~200 -
Alloy Steel 0.06~0.1~0.12 100~180 - Alloy Steel 0.08~0.15~0.2 100~180 -
Mold Steel 0.06~0.08~0.1 80~150 - Mold Steel 0.08~0.12~0.2 80~150 -
Gray Cast Iron 0.08~0.1~0.15 - 100~180 Gray Cast Iron 0.08~0.18~0.25 - 100~180
Nodular Cast Iron 0.06~0.08~0.1 - 80~120 Nodular Cast Iron 0.08~0.15~0.2 - 80~120
JS Chipbreaker Cutting Dia. 20~160
Cutting Dia. 10~18 MEC20~MEC40 MEC40R~MEC160R
MEC10~MEC18
Workpiece Recommended Insert Grade Recommended Insert Grade M
Material (Cutting Speed: m/min) (Cutting Speed: m/min)
fz (mm/t) Workpiece fz (mm/t)
PVD Coated Carbide Material PVD Coated Carbide
PR830 PR1025 PR830 PR1025
Stainless Steel 0.06~0.08~0.1 100~180 100~180 Stainless Steel 0.08~0.1~0.12 100~180 100~180
Carbon Steel 0.06~0.1~0.12 Carbon Steel 0.08~0.15~0.18
0.06~0.08~0.1 120~200 100~150 0.08~0.12~0.15 120~200 100~150 Milling
Alloy Steel 0.06~0.08~0.1 Alloy Steel 0.08~0.1~0.12
Mold Steel 100~180 - Mold Steel 100~180 -
80~150 - 80~150 -
JA Chipbreaker fz (mm/t) Recommended Insert Grade PCD fz (mm/t) Recommended Insert Grade
(Cutting Speed: m/min) (Cutting Speed: m/min)
Workpiece 0.05~0.3 Carbide Workpiece 0.05~0.2 PCD
Material 0.05~0.2 GW25 Material 0.05~0.15
KPD230 (KPD001)
Aluminum Alloy 200~800 Aluminum Alloy
(Si 13% or below) (Si 13% or below) 500~1,500
200~300
Aluminum Alloy Aluminum Alloy 300~1,000
(Si 13% or above) (Si 13% or above)
Warning Please observe below precautions fully. Failure to observe the precautions may cause serious dam-
age to human body.
Warning about Max. Revolution indicated on main body Max. Balance qual-
Revolution ity grade G
1. When running the endmill and the facemill at revolutions exceeding the maximum revolution limit, the inserts or toolholder may be damaged due to
the centrifugal force. (min-1) ISO 1940-1 / 8821
(JIS B0905)
2. For actual practical revolution, please set within recommended machining condition. ~20 000
3. When using at a higher revolution (over 10,000min-1), refer to the table to adjust the balance of MEC and suitable arbor. G16
~30 000 G6.3
30 000~ G2.5
kyocera@kyocera-tools.ru M47
www.kyocera-tools.ru