Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
4PGSL, 5PGSL, 6PGSL
Semi-Finishing Recommended Material Number of Flutes: 4, 5, 6
of Hard Materials (Long)
1st Recommendation
Aluminum Non-ferrous Metal Difficult-to-Cut Material Hardened material General Use I
Shank Dia.
-
456 %D
%T
Lineup (Unit: mm)
Description Std. Outside Dia. Outside Dia. Edge Length Shank Dia. Total length Number of Flutes
Dc tolerance Ds L Z
4PGSL060-210-06 76 4
4PGSL080-280-08 6 -0.020 21 6
5PGSL100-350-10 -0.038
6PGSL120-420-12
6PGSL160-560-16 8 -0.025 28 8 100 4
6PGSL200-700-20 -0.047
6PGSL250-880-25
10 -0.025 35 10 100 5
-0.047
12 -0.032 42 12 125 6
-0.059
16 -0.032 56 16 125 6
-0.059
20 -0.040 70 20 150 6
-0.073
25 -0.040 88 25 150 6
-0.073
L Web thickness ratio is 60% between the cutting edge and 1Dc and 80% for the rest. Good chip evacuation and high rigidity. Best
suitable for high-speed shouldering.
Recommended Cutting Conditions
Shouldering
Solid End Mill Workpiece Depth of Cut (apae) (mm) Outside Dia. (mm) 6 8 10 12 16 20 25
BQ Materials Roughing Finishing
< 30HRC 1Dc0.2Dc 3.5Dc0.1Dc Spindle Revolution (min-1) 10,700 8,000 6,400 5,300 4,000 3,200 2,500
Feed Rate (mm/min) 2,230 2,230 2,870 3,500 3,580 3,440 3,060
Shouldering
30~40HRC 1Dc0.2Dc 3.5Dc0.1Dc Spindle Revolution (min-1) 9,600 7,200 5,700 4,800 3,600 2,900 2,300
Feed Rate (mm/min) 1,810 1,820 2,440 2,870 3,010 2,920 2,610
40~45HRC 1Dc0.2Dc 3.5Dc0.1Dc Spindle Revolution (min-1) 8,500 6,400 5,100 4,200 3,200 2,500 2,000
Steel Feed Rate (mm/min) 1,360 1,400 1,780 2,040 2,080 2,080 2,080
45~50HRC 1Dc0.2Dc 3.5Dc0.1Dc Spindle Revolution (min-1) 6,400 4,800 3,800 3,200 2,400 1,900 1,500 Feed Rate (mm/min) 760 860 1,050 1,340 1,290 1,280 1,280
50~55HRC 1Dc0.2Dc 3.5Dc0.1Dc Spindle Revolution (min-1) 4,200 3,200 2,500 2,100 1,600 1,300 1,000
Feed Rate (mm/min) 340 380 510 570 570 570 550
> 55HRC 1Dc0.2Dc 3.5Dc0.1Dc Spindle Revolution (min-1) 3,700 2,800 2,200 1,900 1,400 1,100 900
Feed Rate (mm/min) 220 220 330 390 420 400 380
Not Recommended for Slotting.
L30 : Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
kyocera@kyocera-tools.ru
www.kyocera-tools.ru