Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
4PGSM, 5PGSM, 6PGSM
Semi-Finishing Recommended Material Number of Flutes: 4, 5, 6
of Hard Materials (Medium)
1st Recommendation
%DI
%T
Shank Dia.
Aluminum Non-ferrous Metal Difficult-to-Cut Material Hardened material General Use
-
456
Lineup (Unit: mm)
Description Std. Outside Dia. Outside Dia. Edge Length Shank Dia. Total length Number of Flutes
Dc tolerance Ds LZ
4PGSM060-150-06
4PGSM080-200-08 6 -0.020 15 6 76 4
5PGSM100-250-10 -0.038
6PGSM120-300-12
6PGSM160-400-16 8 -0.025 20 8 100 4
6PGSM200-500-20 -0.047
6PGSM250-630-25
10 -0.025 25 10 100 5
-0.047
12 -0.032 30 12 125 6
-0.059
16 -0.032 40 16 125 6
-0.059
20 -0.040 50 20 150 6
-0.073
25 -0.040 63 25 150 6
-0.073
Four, ve and six utes types are available for semi-nishing of hardened materials. Web thickness ratio is 60% between the cutting L
edge and 1Dc and 80% for the rest. Good chip evacuation and high rigidity.
Recommended Cutting Conditions
Shouldering
Workpiece Depth of Cut (apae) (mm) Outside Dia. (mm) 6 8 10 12 16 20 25 Solid End Mill
Materials Roughing Finishing
BQ
BF < 30HRC 1Dc0.2Dc Spindle Revolution (min-1) 10,700 8,000 6,400 5,300 4,000 3,200 2,500
2.5Dc0.1Dc 2,240 2,870 3,500 3,580 3,440 3,060
Shouldering 5,700 4,800 3,600 2,900 2,300
Feed Rate (mm/min) 2,240 2,440 2,870 3,010 2,920 2,610
5,100 4,200 3,200 2,500 2,000
30~ 1Dc0.2Dc 2.5Dc0.1Dc Spindle Revolution (min-1) 9,600 7,200 1,780 2,040 2,000 2,000 2,080
40HRC Feed Rate (mm/min) 1,710 1,720 3,800 3,200 2,400 1,900 1,500
1,050 1,340 1,290 1,260 1,260
40~ 1Dc0.2Dc 2.5Dc0.1Dc Spindle Revolution (min-1) 8,500 6,400 2,500 2,100 1,600 1,300 1,000
45HRC 1Dc0.2Dc Feed Rate (mm/min) 1,360 1,400 510 570 570 570 550
2,200 1,900 1,400 1,100 900
Steel 45~ 330 390 420 400 380
50HRC
2.5Dc0.1Dc Spindle Revolution (min-1) 6,400 4,800
Feed Rate (mm/min) 760 860
50~ 1Dc0.2Dc 2.5Dc0.1Dc Spindle Revolution (min-1) 4,200 3,200
55HRC Feed Rate (mm/min) 340 380
> 55HRC 1Dc0.2Dc 2.5Dc0.1Dc Spindle Revolution (min-1) 3,700 2,800
Feed Rate (mm/min) 220 220
Not Recommended for Slotting.
: Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
kyocera@kyocera-tools.ru L29
www.kyocera-tools.ru