Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
4PGSS, 5PGSS
Deep Slotting and Semi-Finishing Recommended Material Number of Flutes: 4, 5
of Hard Materials
1st Recommendation
Aluminum Non-ferrous Metal Difficult-to-Cut Material Hardened material General Use I
Shank Dia.
-
45 %D
%T
Lineup (Unit: mm)
Description Std. Outside Dia. Outside Dia. Edge Length Shank Dia. Total length Number of Flutes
Dc tolerance Ds LZ
4PGSS030-045-06 3 -0.014 4.5 6 57 4
-0.028
4PGSS040-060-06 4 -0.020 6 6 57 4
-0.038
4PGSS050-075-06 5 -0.020 7.5 6 76 4
-0.038
4PGSS060-090-06 6 -0.020 9 6 76 4
-0.038
4PGSS080-120-08 8 -0.025 12 8 100 4
-0.047
4PGSS100-150-10 10 -0.025 15 10 100 4
-0.047
4PGSS120-180-12 12 -0.032 18 12 125 4
-0.059
4PGSS160-240-16 16 -0.032 24 16 125 4
-0.059
L 4PGSS200-300-20 20 -0.040 30 20 150 4
-0.073
5PGSS250-380-25 25 -0.040 38 25 150 5
-0.073
Web thickness ratio is 60% between the cutting edge and 1Dc and 80% for the rest. Good chip evacuation and high rigidity.
Recommended Cutting Conditions
Shouldering
Solid End Mill
Workpiece Depth of Cut (apae) (mm)
BQ Materials
Outside Dia. (mm) 3 6 8 10 12 16 20 25
Roughing Finishing
< 30HRC 1Dc0.2Dc Spindle Revolution (min-1) 21,200 10,600 8,000 6,400 5,300 4,000 3,200 2,500
1.5Dc0.1Dc
BF
Feed Rate (mm/min) 2,400 2,400 2,400 2,400 2,400 2,400 2,400 2,500
Shouldering
30~ 1Dc0.2Dc Spindle Revolutin (min-1) 19,100 9,600 7,200 5,700 4,800 3,600 2,900 2,300
40HRC 1.5Dc0.1Dc
Feed Rate (mm/min) 1,900 1,900 1,900 1,900 1,900 2,000 2,000 2,100
40~ 1Dc0.2Dc Spindle Revolution (min-1) 17,000 8,500 6,400 5,100 4,200 3,200 2,500 2,000
45HRC 1Dc0.2Dc 1.5Dc0.1Dc
45~ Feed Rate (mm/min) 1,400 1,400 1,400 1,400 1,400 1,400 1,400 1,700
50HRC
Steel
Spindle Revolution (min-1) 12,700 6,400 4,800 3,800 3,200 2,400 1,900 1,500
1.5Dc0.1Dc
Feed Rate (mm/min) 850 850 860 860 870 870 870 1,000
50~ 1Dc0.2Dc Spindle Revolution (min-1) 8,500 4,200 3,200 2,500 2,100 1,600 1,300 1,000
55HRC 1.5Dc0.1Dc
Feed Rate (mm/min) 400 400 400 410 410 410 410 450
> 55HRC 1Dc0.2Dc Spindle Revolution (min-1) 7,400 3,700 2,800 2,200 1,900 1,400 1,100 900
1.5Dc0.1Dc 310
Feed Rate (mm/min) 250 250 250 260 260 280 280
Not Recommended for Slotting.
L28 : Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
kyocera@kyocera-tools.ru
www.kyocera-tools.ru