Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
4FEKM
General use / Finishing Recommended Material Number of Flutes: 4
Tough corner edge (Medium)
1st Recommendation
Land %D I
%
Shank Dia.
MEGACOAT is applied %TI
4 Super Micro-grain carbide Aluminum Non-ferrous Metal Difficult-to-Cut Material Hardened material General Use
-
Lineup (Unit: mm) (Unit: mm)
Description Std. Outside Outside Length Neck Under Shank Overall Number Description Std. Outside Outside Length Neck Under Shank Overall Number
Dia. Dia. of edge Dia. Neck Dia. length of Flutes Dia. Dia. of edge Dia. Neck Dia. length of Flutes
4FEKM030-100-06 Length 4FEKM080-190-08 Length
4FEKM035-100-06 4FEKM100-220-10
4FEKM040-110-06 Dc tolerance D1 2 Ds L Z 4FEKM120-260-12 Dc tolerance D1 2 Ds L Z
4FEKM045-110-06 4FEKM140-260-16
4FEKM050-130-06 3.0 0 10.0 3.15 12 6 50 4 4FEKM150-300-16 8.0 -0.005 19.0 - - 8 60 4
4FEKM055-130-06 -0.015 4FEKM160-320-16 -0.025
4FEKM060-130-06
3.5 0 10.0 3.68 12 6 50 4 10.0 -0.005 22.0 - - 10 70 4
-0.015 -0.025
4.0 0 11.0 4.2 13.2 6 50 4 12.0 -0.010 26.0 - - 12 75 4
-0.015 -0.030
4.5 0 11.0 4.7 13.2 6 50 4 14.0 -0.010 26.0 14.2 36.4 16 75 4
-0.015 -0.030
5.0 0 13.0 5.2 15.6 6 50 4 15.0 -0.010 30.0 15.2 42 16 90 4
-0.015 -0.030
5.5 0 13.0 5.7 15.6 6 50 4 16.0 -0.010 32.0 - - 16 90 4
-0.015 -0.030
6.0 0 13.0 - - 6 50 4
-0.020
L
Recommended Cutting Conditions
Shouldering
Workpiece Materials Depth of Cut (apae) (mm) Outside Dia. (mm) 3 4 6 8 10 12 16 Solid End Mill
BQ Carbon Steel 1.5Dc0.1Dc Spindle Revolution (min-1) 10,600 8,000 5,300 4,000 3,200 2,700 2,100
Feed Rate (mm/min) 680 690 770 770 770 770 770
BF Alloy Steel 1.5Dc0.1Dc Spindle Revolution (min-1) 8,800 6,600 4,400 3,300 2,600 2,200 2,000
Feed Rate (mm/min) 500 550 620 630 630 630 610
Shouldering
Pre-hardened Steel 1.5Dc0.1Dc Spindle Revolution (min-1) 6,400 4,800 3,200 2,400 1,900 1,600 1,200
30~45HRC Feed Rate (mm/min) 180 180 180 190 190 190 190
Stainless Steel 1.5Dc0.1Dc Spindle Revolution (min-1) 8,000 6,000 4,000 3,000 2,300 2,000 1,500
Feed Rate (mm/min) 190 200 200 200 210 210 210
* Machining with coolant is recommended for stainless steel.
Not Recommended for Slotting.
: Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
kyocera@kyocera-tools.ru L19
www.kyocera-tools.ru