Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
2FEKM
General use / Finishing Recommended Material Number of Flutes: 2
Tough corner edge (Medium)
1st Recommendation
Aluminum Non-ferrous Metal Difficult-to-Cut Material Hardened material General Use Land I
Shank Dia.
MEGACOAT is applied %D
%
%TI
2
Super Micro-grain carbide -
Lineup (Unit: mm) (Unit: mm)
Description Outside Outside Length Neck Under Shank Overall Number Description Outside Outside Length Neck Under Shank Overall Number
Std. Dia. Dia. of edge Dia. Neck Dia. length of Flutes Std. Dia. Dia. of edge Dia. Neck Dia. length of Flutes
Length Length
Dc tolerance D1 2 Ds L Z Dc tolerance D1 2 Ds L Z
2FEKM030-100-06 3.0 0 10.0 3.15 12.0 6 50 2 2FEKM085-190-10 8.5 -0.005 19.0 8.7 26.6 10 70 2
-0.015 -0.025
2FEKM035-100-06 3.5 0 10.0 3.68 12.0 6 50 2 2FEKM090-190-10 9.0 -0.005 19.0 9.2 26.6 10 70 2
-0.015 -0.025
2FEKM040-110-06 4.0 0 11.0 4.2 13.2 6 50 2 2FEKM095-190-10 9.5 -0.005 19.0 9.7 26.6 10 70 2
-0.015 -0.025
2FEKM045-110-06 4.5 0 11.0 4.7 13.2 6 50 2 2FEKM100-220-10 10.0 -0.005 22.0 - - 10 70 2
-0.015 -0.025
2FEKM050-130-06 5.0 0 13.0 5.2 15.6 6 50 2 2FEKM110-220-12 11.0 -0.005 22.0 11.2 30.8 12 75 2
-0.015 -0.025
2FEKM055-130-06 5.5 0 13.0 5.7 15.6 6 50 2 2FEKM120-260-12 12.0 -0.010 26.0 - - 12 75 2
-0.015 -0.030
2FEKM060-130-06 6.0 0 13.0 - - 6 50 2 2FEKM130-260-16 13.0 -0.010 26.0 13.2 36.4 16 75 2
-0.020 -0.030
2FEKM065-160-08 6.5 0 16.0 6.7 22.4 8 60 2 2FEKM140-260-16 14.0 -0.010 26.0 14.2 36.4 16 75 2
-0.020 -0.030
2FEKM070-160-08 7.0 0 16.0 7.2 22.4 8 60 2 2FEKM150-300-16 15.0 -0.010 30.0 15.2 42.0 16 90 2
-0.020 -0.030
2FEKM075-190-08 7.5 0 19.0 7.7 26.6 8 60 2 2FEKM160-320-16 16.0 -0.010 32.0 - - 16 90 2
-0.020 8 60 2 -0.030
L
2FEKM080-190-08 8.0 -0.005 19.0 - -
-0.025
Recommended Cutting Conditions
Solid End Mill Shouldering
BQ Workpiece Materials Depth of Cut (apae) (mm) Outside Dia. (mm) 3 4 6 8 10 12 16
Carbon Steel 1.5Dc0.1Dc Spindle Revolution (min-1) 9,300 7,000 4,600 3,500 3,000 2,700 2,200
Feed Rate (mm/min) 450 450 470 470 470 470 440
BF Alloy Steel 1.5Dc0.1Dc Spindle Revolution (min-1) 8,800 6,600 4,400 3,300 2,600 2,200 1,800
Feed Rate (mm/min) 370 370 380 380 380 380 360
Shouldering
Pre-hardened Steel 1.5Dc0.1Dc Spindle Revolution (min-1) 6,400 4,800 3,200 2,400 1,900 1,600 1,200
Slotting 30~45HRC Feed Rate (mm/min) 130 130 130 140 140 140 140
BQ Spindle Revolution (min-1) 8,000 6,000 4,000 3,000 2,400 2,000 1,500
Feed Rate (mm/min) 140 140 140 140 140 140 140
Stainless Steel 1.5Dc0.1Dc
* Machining with coolant is recommended for stainless steel.
Please refer to page L44 about Slotting.
L18 : Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
kyocera@kyocera-tools.ru
www.kyocera-tools.ru