Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
3UFSM
General use / Semi-Finishing Recommended Material Number of Flutes: 3
1st Recommendation
Aluminum Non-ferrous Metal Difficult-to-Cut Material Hardened material General Use I
Shank Dia.
3 Dc
Ds
Lineup
(Unit: mm)
Description Std. Outside Dia. Outside Dia. Edge Length Shank Dia. Total length Number of Flutes
Dc tolerance Ds LZ
3UFSM010-030-04 1 -0.014 3 4 50 3
-0.028
3UFSM015-030-04 1.5 -0.014 3 4 50 3
-0.028
3UFSM020-030-04 2 -0.014 3 4 50 3
-0.028
3UFSM025-040-04 2.5 -0.014 4 4 50 3
-0.028
3UFSM030-080-06 3 -0.014 8 6 50 3
-0.028
3UFSM040-120-06 4 -0.020 12 6 50 3
-0.038
3UFSM050-140-06 5 -0.020 14 6 50 3
-0.038
3UFSM060-160-06 6 -0.020 16 6 50 3
-0.038
L 3UFSM080-200-08 8 -0.025 20 8 63 3
-0.047
3UFSM100-220-10 10 -0.025 22 10 76 3
-0.047
3UFSM120-250-12 12 -0.032 25 12 76 3
-0.059
3UFSM160-320-16 16 -0.032 32 16 89 3
-0.059
Solid End Mill 3UFSM200-380-20 20 -0.040 38 20 104 3
-0.073
BQ
Products emphasizing high efciency machining, three utes type for general semi nishing. It is available for slotting and shouldering
of wide range of work materials.
Recommended Cutting Conditions
Shouldering
Workpiece Depth of Cut Outside Dia. 2 3 4 5 6 8 10 12 16 20
Materials
(apae) (mm) (mm)
Carbon Steel 1.0Dc0.1Dc Spindle Revolution (min-1) 16,000 10,600 8,000 6,400 5,300 4,000 3,200 2,700 2,000 1,600
Cast Iron Feed Rate (mm/min) 330 330 390 420 430 450 480 480 510 530
BF Alloy Steel 1.0Dc0.1Dc Spindle Revolution (min-1) 11,000 7,400 5,600 4,500 3,700 2,800 2,200 1,900 1,400 1,100
(~30HRC) Feed Rate (mm/min) 240 290 290 310 330 330 340 340 340 340
Shouldering
Pre-hardened Steel 1.0Dc0.1Dc Spindle Revolution (min-1) 8,000 5,300 4,000 3,200 2,700 2,000 1,600 1,300 1,000 800
Stainless Steel Feed Rate (mm/min) 140 140 140 170 180 180 190 190 190 190
(30~40HRC)
BQ Spindle Revolution (min-1) 4,000 2,700 2,000 1,600 1,300 1,000 800 700 500 400
Titanium Alloy
Heat-resistant Alloy 1.0Dc0.1Dc
(40~50HRC) Feed Rate (mm/min) 40 50 60 60 70 70 70 70 80 80
Slotting Spindle Revolution (min-1) 32,000 21,000 16,000 12,800 10,600 8,000 6,400 5,300 4,000 3,200
Feed Rate (mm/min) 670 700 760 820 860 880 1,000 1,100 1,100 1,250
Aluminum Alloy 1.0Dc0.1Dc
* Machining with coolant is recommended for stainless steel.
For Slotting, see page L44
L20 : Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
kyocera@kyocera-tools.ru
www.kyocera-tools.ru