Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
2FEKS
General use / Finishing Recommended Material Number of Flutes: 2
Tough corner edge (Short)
1st Recommendation
Land I Dsh5
Shank Dia. Aluminum Non-ferrous Metal Difficult-to-Cut Material Hardened material General Use
MEGACOAT is applied Dc
D1
2
30°
Super Micro-grain carbide
L
Lineup (Unit: mm) (Unit: mm)
Description Std. Outside Outside Length Neck Under Neck Shank Overall Number Std. Outside Outside Length Neck Under Neck Shank Overall Number
Dia. Dia. of edge Dia. Length Dia. length of Flutes Dia. Dia. of edge Dia. Length Dia. length of Flutes
2FEKS030-045-06 toler- Description toler-
2FEKS035-052-06 Dc ance D1 2 Ds L Dc ance D1 2 Ds L
2FEKS040-060-06 Z 2FEKS080-120-08 Z
2FEKS045-067-06 2FEKS100-150-10
2FEKS050-075-06 3.0 0 4.5 3.15 6.5 6 50 2 2FEKS120-180-12 8.0 -0.005 12.0 - - 8 60 2
2FEKS055-082-06 -0.015 2FEKS140-210-16 -0.025
2FEKS060-090-06 2FEKS150-230-16
3.5 0 5.2 3.68 7.2 6 50 2 2FEKS160-240-16 10.0 -0.005 15.0 - - 10 70 2
-0.015 -0.025
4.0 0 6.0 4.2 8.2 6 50 2 12.0 -0.010 18.0 - - 12 75 2
-0.015 -0.030
4.5 0 6.7 4.7 8.9 6 50 2 14.0 -0.010 21.0 14.2 31.4 16 75 2
-0.015 -0.030
5.0 0 7.5 5.2 10.1 6 50 2 15.0 -0.010 23.0 15.2 35 16 90 2
-0.015 -0.030
5.5 0 8.2 5.7 10.8 6 50 2 16.0 -0.010 24.0 - - 16 90 2
-0.015 -0.030
6.0 0 9.0 - - 6 50 2
-0.020
Corner lands improve the cutting edge strength. L
Recommended Cutting Conditions
Shouldering
Workpiece Materials Depth of Cut (apae) (mm) Outside Dia. (mm) 3 4 6 8 10 12 16 Solid End Mill
BQ Carbon Steel 1.2Dc0.1Dc Spindle Revolution (min-1) 9,300 7,000 4,600 3,500 3,000 2,700 2,200
BQ Feed Rate (mm/min) 450 450 470 470 470 470 440
BF Alloy Steel 1.2Dc0.1Dc Spindle Revolution (min-1) 8,800 6,600 4,400 3,300 2,600 2,200 1,800
Feed Rate (mm/min) 370 370 380 380 380 380 360
Shouldering
Pre-hardened Steel 1.2Dc0.1Dc Spindle Revolution (min-1) 6,400 4,800 3,200 2,400 1,900 1,600 1,200
30~45HRC Feed Rate (mm/min) 130 130 130 140 140 140 140
Stainless Steel 1.2Dc0.1Dc Spindle Revolution (min-1) 8,000 6,000 4,000 3,000 2,400 2,000 1,500
Feed Rate (mm/min) 140 140 140 140 140 140 140
Slotting
* Machining with coolant is recommended for stainless steel.
For Slotting, see page L44.
: Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
kyocera@kyocera-tools.ru L17
www.kyocera-tools.ru