Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
4FESM
General use / Finishing (Medium) Recommended Material Number of Flutes: 4
1st Recommendation
Aluminum Non-ferrous Metal Difficult-to-Cut Material Hardened material General Use Sharp I
Std.
Shank Dia.
MEGACOAT is applied Dc Dsh5
D1
4
30°
Super Micro-grain carbide
L
Lineup (Unit: mm) (Unit: mm)
Description Outside Outside Length of Neck Shank Overall Number Description Std. Outside Outside Length of Neck Shank Overall Number
Dia. Dia. edge Dia. Dia. length of Flutes Dia. Dia. edge Dia. Dia. length of Flutes
toler- toler-
D1 D1
Dc ance Ds L Z Dc ance Ds L Z
4FESM010-025-04 1.0 0 2.5 1.1 4 45 4 4FESM055-130-06 5.5 0 13.0 5.7 6 50 4
-0.015 -0.015
4FESM015-040-04 1.5 0 4.0 1.6 4 45 4 4FESM060-130-06 6.0 0 13.0 - 6 50 4
-0.015 -0.020
4FESM020-060-04 2.0 0 6.0 2.1 4 45 4 4FESM080-190-08 8.0 -0.005 19.0 - 8 60 4
-0.015 -0.025
4FESM025-080-04 2.5 0 8.0 2.6 4 45 4 4FESM100-220-10 10.0 -0.005 22.0 - 10 70 4
-0.015 -0.025
4FESM030-100-06 3.0 0 10.0 3.2 6 50 4 4FESM120-260-12 12.0 -0.010 26.0 - 12 75 4
-0.015 -0.030
4FESM035-100-06 3.5 0 10.0 3.7 6 50 4 4FESM140-260-16 14.0 -0.010 26.0 14.2 16 75 4
-0.015 -0.030
4FESM040-110-06 4.0 0 11.0 4.2 6 50 4 4FESM150-300-16 15.0 -0.010 30.0 15.2 16 90 4
-0.015 -0.030
4FESM045-110-06 4.5 0 11.0 4.7 6 50 4 4FESM160-320-16 16.0 -0.010 32.0 - 16 90 4
-0.015 -0.030
4FESM050-130-06 5.0 0 13.0 5.2 6 50 4
-0.015
L
Recommended Cutting Conditions
Shouldering
Solid End Mill Workpiece Materials Depth of Cut (apae) (mm) Outside Dia. (mm) 1 2 4 6 8 12 16
BQ
BF Carbon Steel 1.5Dc0.05Dc Spindle Revolution (min-1) 25,500 13,000 6,600 4,400 3,300 2,200 1,700
(Dc<3) Feed Rate (mm/min) 335 345 580 620 625 630 600
Shouldering Alloy Steel
1.5Dc0.1Dc Spindle Revolution (min-1) 22,000 11,000 5,600 3,700 2,800 1,900 1,400
Pre-hardened Steel (Dc 3) Feed Rate (mm/min) 290 290 395 455 455 470 460
30~45HRC
1.5Dc0.05Dc Spindle Revolution (min-1) 12,000 7,200 4,200 3,000 2,200 1,500 1,100
Stainless Steel (Dc<3) Feed Rate (mm/min) 105 125 150 160 160 165 140
1.5Dc0.1Dc Spindle Revolution (min-1) 22,000 11,000 5,600 3,700 2,800 1,900 1,400
(Dc 3) Feed Rate (mm/min) 130 145 165 165 170 175 155
1.5Dc0.05Dc
(Dc<3)
1.5Dc0.1Dc
(Dc 3)
1.5Dc0.05Dc
(Dc<3)
1.5Dc0.1Dc
(Dc 3)
* Machining with coolant is recommended for stainless steel.
Not Recommended for Slotting.
L16 : Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
kyocera@kyocera-tools.ru
www.kyocera-tools.ru