Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
MagicDrill® DRX type
DRX (Cutting Depth: 3D) -
Y% -
-
Std. E
No. of Insert E
Toolholder Dimensions %D Spare Parts 3D
Description Dimension (mm)
L1 L2 L3 d Max. Clamp Screw Wrench Applicable Inserts
Offset K22
Dc (Radial)
d1 (mm)
S20 -DRX135M-3-04 13.5 105 62 40.5 +0.5
-DRX140M-3-04 2 14 106 63 42 20 27 +0.4 SB-2042TRG DTM-6 ZXMT040203
14.5 108 65 43.5 +0.3 DTM-6 ZXMT05T203
-DRX145M-3-04 DTM-7 ZXMT06T204
DTM-8 ZXMT070305
-DRX150M-3-04 15 109 66 45 +0.2
DTM-10 ZXMT09T306
S25 -DRX155M-3-05 15.5 124 70 46.5 +0.8 DTM-15 ZXMT11T306
-DRX160M-3-05 16 126 71 48 +0.7
-DRX165M-3-05 2 16.5 127 73 49.5 25 32 +0.5 SB-2045TR
17 129 74 51 +0.4
-DRX170M-3-05
-DRX175M-3-05 17.5 130 76 52.5 +0.3
-DRX180M-3-05 18 132 77 54 +0.2
-DRX185M-3-06 18.5 131 77 55.5 +0.9
-DRX190M-3-06 19 132 78 57 +0.8
K -DRX195M-3-06 19.5 134 80 58.5 +0.7
-DRX200M-3-06
2 20 135 81 60 25 32 +0.5 SB-2250TR
-DRX205M-3-06 20.5 137 83 61.5 +0.4
-DRX210M-3-06 21 138 84 63 +0.3
-DRX215M-3-06 21.5 140 86 64.5 +0.2
-DRX220M-3-07 22 141 86 66 +1.2
Drilling -DRX225M-3-07 22.5 142 88 67.5 +1.0
-DRX230M-3-07 23 144 89 69 +0.9
-DRX235M-3-07 23.5 145 91 70.5 +0.8
-DRX240M-3-07 2 24 147 92 72 25 35 +0.7 SB-2570TR
-DRX245M-3-07 24.5 148 94 73.5 +0.5
-DRX250M-3-07 25 150 95 75 +0.4
-DRX255M-3-07 25.5 151 97 76.5 +0.3
-DRX260M-3-07 26 153 98 78 +0.2
S32 -DRX265M-3-09 26.5 161 102 79.5 +1.7
-DRX270M-3-09 27 163 103 81 +1.6
-DRX275M-3-09 27.5 164 105 82.5 42 +1.5
28 166 106 84 +1.3
-DRX280M-3-09
-DRX285M-3-09 28.5 167 108 85.5 +1.2
-DRX290M-3-09 2 29 169 109 87 32 +1.1 SB-3080TR
-DRX295M-3-09 29.5 170 111 88.5 +1.1
-DRX300M-3-09 30 172 112 90 +0.8
-DRX305M-3-09 30.5 173 114 91.5 45 +0.7
-DRX310M-3-09 31 175 115 93 +0.6
-DRX315M-3-09 31.5 176 117 94.5 +0.5
S40 -DRX320M-3-11 32 201 132 96 +2.2
-DRX330M-3-11 33 204 135 99 +1.9
-DRX340M-3-11 34 207 138 102 +1.7
-DRX350M-3-11 2 35 210 141 105 40 55 +1.4 SB-4085TR
-DRX360M-3-11 36 213 144 108 +1.2
-DRX370M-3-11 37 216 147 111 +0.9
-DRX380M-3-11 38 219 150 114 +0.7
• When offset machining, reduce feed rate to 0.08mm/rev. or less. For recommended cutting conditions, see page K32
• See K33 for Adjustable Sleeve (SHE type). For troubleshooting, see page K31
• Cutting tolerance (3D type)
Dc Cutting tolerance (mm)
13.5~26 +0.20
-0.10
26.5~38 +0.25
-0.15
39~60 +0.30
-0.20
* Above is numeric guideline.
It may vary depending on machines / workpieces / clamp status / cutting conditions.
K26 : Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
kyocera@kyocera-tools.ru
www.kyocera-tols.ru