Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
Toolholder Dimensions Spare Parts 2D
Description
Applicable Inserts
K22
Std. Dimension (mm) Max. Clamp Screw Wrench
No. of InsertL1 L2 L3 d Offset
DrillingDc(Radial)
d1 (mm)
S40 -DRX320M-2-11 32 169 100 64 +2.2
-DRX330M-2-11 33 171 102 66 +1.9
-DRX340M-2-11 34 173 104 68 +1.7
-DRX350M-2-11 2 35 175 106 70 40 55 +1.4 SB-4085TR DTM-15 ZXMT11T306
-DRX360M-2-11 36 177 108 72 +1.2
-DRX370M-2-11 37 179 110 74 +0.9
-DRX380M-2-11 38 181 112 76 +0.7
-DRX390M-2-14 39 179 110 78 +2.8
-DRX400M-2-14 40 181 112 80 55 +2.5
-DRX410M-2-14 41 183 114 82 +2.3
-DRX420M-2-14 42 185 116 84 +2.0
-DRX430M-2-14 2 43 187 118 86 40 +1.8 SB-5090TR DT-20 ZXMT140408
-DRX440M-2-14 44 189 120 88 +1.5
-DRX450M-2-14 45 191 122 90 60 +1.3
-DRX460M-2-14 46 193 124 92 +1.0
-DRX470M-2-14 47 195 126 94 +0.8
-DRX480M-2-17 48 194 125 96 +3.8
-DRX490M-2-17 49 196 127 98 +3.5
-DRX500M-2-17 50 198 129 100 60 +3.3
-DRX510M-2-17 51 200 131 102 +3.0
-DRX520M-2-17 52 202 133 104 +2.8 DT-25 ZXMT170608
-DRX530M-2-17 53 204 135 106 +2.5
-DRX540M-2-17 2 54 206 137 108 40 +2.3 SB-60120TR
-DRX550M-2-17 55 208 139 110 +2.0 K
-DRX560M-2-17 56 210 141 112 +1.8
-DRX570M-2-17 57 212 143 114 65 +1.5
-DRX580M-2-17 58 214 145 116 +1.3
-DRX590M-2-17 59 216 147 118 +1.0
-DRX600M-2-17 60 218 149 120 +0.8
When offset machining, reduce feed rate to 0.08mm/rev. or less. For recommended cutting conditions, see page K32
See K33 for Adjustable Sleeve (SHE type). For troubleshooting, see page K31
Cutting tolerance (2D type)
Dc Cutting tolerance (mm)
13.5~26 +0.20
-0.10
27~38 +0.25
-0.15
39~60 +0.30
-0.20
* Above is numeric guideline.
It may vary depending on machines / workpieces / clamp status / cutting conditions.
: Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
kyocera@kyocera-tools.ru K25
www.kyocera-tools.ru