Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
Face Grooving Toolholders [GVF Insert]
GFV
T
(ToFaocueteGr droiao.v)ing Dia. D 2F L2 L1 H1 H3 B Fa(cTeoGouroteorvidniga.D) ia. D
HeaDd1dia1meterh Head diaDm1eter
L3
GFV 2020K 201A L3
GFV 2525M 201A
Shows right Figure.
Right-hand Shown Left-hand Shown
R-hand Insert is for R-hand Toolholder, L-hand Insert is for L-hand Toolholder.
G Toolholder Dimensions Dimension (mm) Face Grooving Dia. Spare Parts
D
Std. Clamp Set Wrench Applicable
Description Inserts
G65
R L H1 h H3 B L1 L2 L3 F T D1 MIN. MAX.
LW
Grooving FT
GFV 2020K-201A 20 21 6.5 20 125 20 19 25 2.2 40 20 CPS-5V - FT-15 GVF 200A~340A
2525M-201A 25 26 25 150 23 22 32 (12) GVF 100AR~150AR
GFV 2020K-351B 20 21 20 125 28 26 25 4.6 GVF 250B~350B
2525M-351B 25 26 25 150 30 28 32 5.1 GVF 150BR
2020K-352B 20 21 20 125 28 26 25 35 35 50 GVF 400B~490B
2525M-352B 25 26 25 150 30 28 32 (25) () GVF 200BR
2020K-501B 20 21 8.0 20 125 28 26 25 4.6 50 50 70 - CPS-6V LW-3 GVF 250B~350B
2525M-501B 25 26 25 150 30 28 32 5.1 (25) () GVF 150BR
2020K-502B 20 21 20 125 28 26 25 GVF 400B~490B
2525M-502B 25 26 25 150 30 28 32 GVF 200BR
2020K-701B 20 21 20 125 28 26 25 4.6 70 70 100 GVF 250B~350B
2525M-701B 25 26 25 150 30 28 32 5.1 (25) () GVF 150BR
2020K-702B 20 21 20 125 28 26 25 GVF 400B~490B
2525M-702B 25 26 25 150 30 28 32 GVF 200BR
GFV 2525M-501C 6.6 50 50 70 GVF 350C~450C
2525M-502C 8.1 (25) () GVF 500C~600C
2525M-701C 33 100 GVF 350C~450C
2525M-702C 35 6.6 70 70 () GVF 500C~600C
2525M-1001C 8.1 (25) 150 GVF 350C~450C
2525M-1002C 25 26 9.5 25 150 35 32 () - CPS-8V LW-4 GVF 500C~600C
6.6 100
8.1 100 (25)
2525M-1501C 6.6 150 150 250 GVF 350C~450C
2525M-1502C 8.1 (25) () GVF 500C~600C
Note1. Dimension T shows available grooving depth.
2. D1 shows toolholder head diameter to L3.
3. The value ( ) of Face Grooving Dia. (D Max) is the maximum outer diameter value after the initial groove between MIN~MAX. (It is possible to widen the groove to infinity ).
The value ( ) of Face Grooving Dia. (D Min) is the minimum diameter of the boss which remains in the center when widening the groove width to a smaller value after the initial
groove between MIN~MAX.
4. Standard toolholders are designed with the edge position 1.0mm above the center. When using non-standard Toolholders, set the Edge position 1.0mm above the center.
Selection of Toolholder & Insert
Toolholder R-hand Toolholder L-hand
Insert R-hand Insert L-hand
G60 : Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
kyocera@kyocera-tools.ru
www.kyocera-tools.ru