Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
Grooving Inserts
Applicable Inserts P Carbon Steel / Alloy Steel Classification of usage
M Stainless Steel
(mm) K Cast Iron : Continuous-Light Interruption /
N Non-ferrous Metals 1st Choice
Description ALH S Titanium Alloy : Continuous-Light Interruption /
Hard materials (under 40HRC) 2nd Choice
GVF …-100AA H Hard materials (over 40HRC) : Continuous / 1st Choice
…-200AA 4.3 12 4.5 : Continuous / 2nd Choice
…-300AA Dimension
(mm) PCD
TN90Cermet PVD
W B r TC40 Coated Applicable
(Previous TC60 Carbide Toolholder
Description) 1.00 PR630
Insert Description PR930 GFVS …-08AA
2.00 2.2 0.05 KW10 Carbide G58
R-hand shown KPD001
KPD010 GFVT …-08AA
r Ref. Page for
GVF Toolholder
2rHA 100-005AA GVF 100AA
B W 0.05 200-005AA 200AA
L
10 10 300-005AA 300AA 3.00
Dimension B: shows available grooving depth.
GVF …005AA inserts are not compatible with GVF …A (see page G65) inserts because their Side Relief Angle is 10.
Face Grooving Diameter of GFVS-AA (also GFVT-AA) G
Description Face Grooving It is available to infinity in case of machining
Dia. D Applicable Inserts the first groove bigger than MIN.
GFVS 1010F-08AA It is available to infinity when machining
1212H-08AA 8 toward outer diameter.
1616H-08AA GVFL/R100AA Grooving
2020K-08AA (0) ( ) ~
2525M-08AA
GVFL/R300AA
Refers to the machining of the initial groove with MIN.8. When widening the groove width to inner diameter.
For machining up to the center of the workpiece
If the initial groove is made smaller than this, regardless of insert width.
the toolholder interferes with the workpiece.
8 (MIN.Face Grooving Dia) 8 (MIN.Face Grooving Dia)
8 (MIN.Face Grooving Dia) 6 (Boss Dia.) 8 (MIN.Face Grooving Dia) 2 (Boss Dia.)
1 (width)
3 (width) 4 4
(Widening the Groove (Widening the Groove
Installing GVFL100AA Installing GVFL300AA Width to Center) Width to Center)
Installing GVFL100AA Installing GVFL300AA
Recommended Cutting Conditions (GFVS-AA / GFVT-AA)
Recommended Insert Grade (Cutting Speed: m/min) Grooving Traversing*
PVD Coated Carbide Carbide
Workpiece PR630 Remarks
PR930
Material KW10 f ap f
(mm) (mm/rev)
(mm/rev)
Carbon Steel / Alloy Steel 50 100 50 100 0.01 0.05 Max.0.5 0.01 0.05
Stainless Steel 50 80 50 80 0.01 0.03 Max.0.3 0.01 0.02 Coolant
Non-ferrous Metals 200 0.01 0.08 Max.0.5 0.01 0.08
* ap has to be set for less than corner-R(r) when traversing of edge width : 1st Recommendation : 2nd Recommendation
1.0 mm (GVF 100AA).
: Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) Inserts are sold
in 10 piece boxes.
kyocera@kyocera-tools.ru G59
www.kyocera-tools.ru