Ниже представлена эта же страница в формате, позволяющем производить копирование текста.

Kyocera - Каталог Токарный инструмент 2016 ENG

                                                                    для заказа - kyocera@kyocera-tools.ru

CUT-OFF TOOLHOLDERS (SMALL DIAMETER)

                                                                                                 Main Spindle            Sub Spindle

 2) When using both Main and Sub spindles                                                                                            0.039”                          GRADES                   A
                                                                                                                                          D2                                                  B
  	In this case, when the cutting edge runs beyond the center line, the insert will                                                                                                           C
       contact the workpiece, since the workpiece does not fall off.                                    Fig.3                                     Fig.4               INSERTS                  D
                                                                                       (When the edge is at the center)  (When the edge is 0.008” beyond the center)                           E
  	 Therefore the programmed distance beyond the center must be considered.                                                                                                                    F
  	e.g. When the cutting edge is programmed to run 1mm beyond the center.                                                                                                                    G
  	 Workpiece maximum, D2 (Fig.4) = [Dmax - 0.039"2] (in)                                                                                                                                   H
	 (The clearance between the insert and the workpiece is 0.008")                                                                                                                              J
                                                                                                                                                                                               N
 T ough Edge Type T Chipbreaker                                                                                                                                     CBN & PCD                P
                                                                                                                                                                                               R
 F racture Resistance Comparison (Interrupted Machining)                                                                                                                                     T

    Tough Edge Type         Competitor A                              Competitor B                                       Cutting Conditions                           TOOLHOLDERS SMALL TOOLS
T Chipbreaker (PR1225)       700 Passes                               3,000 Passes                                       Vc=250 f=0.0020ipr (Cut-Off 0.0006ipr)
                                                                                                                         Wet W1-9 (with flat cuts on two sides)
       3,000 Passes                                                                                                      TKF12R200-T-16DR (PR1225)

                            Fracture of Corner                          Fracture of Corner

                            1,000 Passes                2,000 Passes       3,000 Passes                                                                               BORING

 Tough Edge Type T                                                                                                       Worpiece (with flat cuts on two sides)
Chipbreaker (PR1225)
                                             X                                                                                                                        GROOVING
        Competitor A

Competitor B                                                                                     X

Compared to Competitor A and B, Tough Edge "T Chipbreaker" achieves superior fracture                                                                                 CUT-OFF
resistance during interrupted cutting.

 H ow to Select Edge Preparation

 T roubleshooting

                                                        Lead Angle ()                      Countermeasures                    Name of Chipbreaker                    THREADING
                                                                                       Edge Width                        S T NB

                                                        No (0°)       Yes             Narrower      Wider

Problems                    Countermeasures                                                                                                                           HSK TOOLING SPARE PARTS

Insert Fracture             Insert Fracture Prevention  Effective                                   Effective                         Effective  Effective
                                                        Effective                                   Effective                         Effective  Effective
Long Cutting Time           Cutting Time Reduction      Effective                                                                                                     TECHNICAL

Entangled Chips             Chip Entanglement                                         Effective                Effective
                                 Prevention                                           Effective                Effective
                                                                                      Effective                Effective
Large Boss Remains          Small Boss Remains                        Effective       Effective                Effective
                                                                      Effective
       Ring Remains            Prevention of Ring                     Effective                                                                                       INDEX
    (Hollow Workpiece)      Preventing Deformation
Deformation of thin walled

      workpiece (pipe)

                                                                   kyocera@kyocera-tools.ru                                                                           H9
                                                                      www.kyocera-tools.ru
Заявка