для заказа - kyocera@kyocera-tools.ru
CUT-OFF TOOLHOLDERS (SMALL DIAMETER)
K TKF (For Small Diameter Cut-Off)
T
T
F11 2 0.079” 1 Clamp Screw can be operated from both front and back sides. H1 B
F2KTKF§8-12JX-..(F2=0.394”) h Dmax
H1 BKTKF§8-16JX-..(F2=0.472”) F1
shown above
KTKF§10.. L2 L1 Fig.1
shown above KTKF§6-12JX-..
shown above Right-hand Insert for Right-hand Toolholder
Right-hand Shown
(Goose-neck Holder) T
T
1 F1 0.315”
KTKFL52-12JX F1
shown above
L1 1
h
Fig.2
Left-hand Shown Left-hand Insert for Left-hand Toolholder
T oolholder Dimensions
Stock Dimensions Spare Parts
RL L1 L2
Part Number Unit Shape Clamp Screw Wrench Applicable
H1=h Inserts
B F1 T
H6~H7
KTKF§ 6-12JX 0.375 0.375 4.750 0.590 0.375 0.236 Fig.1
H 8-12JXCUT-OFF 0.500 0.500 4.750 - 0.500 0.236 Fig.1 SB-4590TRWN LTW-10S TKF12§…
0.625 0.625 4.750 - 0.625 0.236 Fig.1
10-12JX
KTKF§ 6-16JX inch 0.375 0.375 4.750 0.787 0.375 0.630 Fig.1 SB-4590TRWN LTW-10S TKF16§…
8-16JX 0.500 0.500 4.750 - 0.500 0.630 Fig.1
10-16JX 0.625 0.625 4.750 - 0.625 0.630 Fig.1
KTKF§ 52-12JX 0.500 0.625 4.750 - 0.625 0.236 Fig.1 LTW-10S TKF12§…
62.5-12JX SB-4590TRWN
0.625 0.750 4.750 - 0.750 0.236 Fig.1
KTKF§ 1010JX-12 10 10 120 15 10 6 Fig.1
1212JX-12 12 12 120 - 12 6 Fig.1 LTW-10S TKF12§…
1616JX-12 16 16 120 - 16 SB-4590TRWN
6 Fig.1
2020JX-12 20 20 120 - 20 6 Fig.1
KTKF§ 1010JX-16 10 10 120 20 10 8 Fig.1
1212JX-16 mm 12 12 120 - 12 8 Fig.1 LTW-10S TKF16§…
1616JX-16 16 16 120 - 16 SB-4590TRWN
8 Fig.1
2020JX-16 20 20 120 - 20 8 Fig.1
KTKF§ 1212F-12 12 12 85 - 12 6 Fig.1 LTW-10S TKF12§…
1212F-16 12 12 85 - 12 SB-4590TRWN TKF16§…
8 Fig.1
KTKF§ 1216JX-12 12 16 120 - 16 6 ig.2 LTW-10S TKF12L…
1620JX-12 16 20 120 - 20 SB-4590TRWN
6 Fig.2
• Dimension T shows the distance from the toolholder to the cutting edge. Recommended Cutting Conditions H32
• See Page H6~H7 for actual cutting diameter.
Note : Cutting diameter of -12 type toolholder (Dmax) depends on the insert grooving width. Main Spindle
H ow to Use D1
1) When using main spindle only 0.039”
W orkpiece maximum D1 (Fig.1)=Dmax
E ven if the cutting edge runs beyond the center line, the insert does not
contact the workpiece, since the workpiece falls off.
(The clearance between the insert and the workpiece is 0.008")
Fig.1 Fig.2
(When the edge is at the center) (When the edge is 0.008” beyond the center)
H8 kyocera@kyocera-tools.ru U.S. Stock Standard :
www.kyocera-tools.ru World Express (Shipping: 7-10 Business Days) :