Kyocera - Инструмент для обработки мелких деталей 2016 ENG

                                                                                   для заказа - kyocera@kyocera-tools.ru

                              MECX

                               Cutting Performance of MECX End Mill                                                                              (JT chipbreaker Vc=400 SFM Workpiece :1049)

A  GRADES                                                          Overhang        Part Number                                        Shouldering               Slotting
                                                                 Length A (in)                                                       (Cutting width ae = D/2)   Ramping and Helical Milling
                              Cutting                            (Colors Refer to
                                Dia.    Part Number (mm / inch)

                                                                 charts on right)

B  INSERTS                    8mm MECX08-S10-07-1T              0.630 -             MECX08-S10-07-1T
                                                                                   MECX0375-S375-07-1T
                              0.375in  MECX0375-S375-07-1T      0.670    -
                              10mm     MECX10-S10-07-1T                             MECX10-S10-07-1T

C  CBN & PCD                  0.500in  MECX0500-S500-07-2T      0.709    1.18
                              12mm     MECX12-S12-07-2T

                              0.625in  MECX0625-S625-07-4T      0.787    1.57
                              16mm     MECX16-S16-07-3T

E  TURNING                    0.750in  MECX0750-S750-07-4T      0.787    1.57
                              20mm     MECX20-S20-07-4T

                                                                                                                MECX0500-S500-07-2TBORING
                                                                                                                   MECX12-S12-07-2T

F

G  GROOVING                                                                        MECX0625-S625-07-4T
                                                                                     MECX16-S16-07-3T
H • Machining with extended overhang length is notCUT-OFF
                                                                                   MECX0750-S750-07-4T
               recommended for 0.315" and 0.394".                                  MECX20-S20-07-4T

   SOLID END MILLS THREADING  • The cutting performance chart shows the
                              applicable range of JT Chipbreaker (PR830) with
J                             standard flute-number type.

                              For Multi-Edge type, use with 70% or less of ap.

               Cutting conditions of JS Chipbreaker

L  For MECX0375~MECX0500 / MECX08~MECX12

                  Decrease the feed rate by 25% according to
                  cutting capability list.

                               For MECX 0625 / MECX16 and over

M  MILLING                    Decrease the feed rate and ap by 30% according
                              to cutting application chart

P  SPARE PARTS

                                        Warning Please observe below precautions fully. Failure to observe the precautions may cause serious damage to human body.

                 Warning about Max. Revolution indicated on main bodyTECHNICAL                                                                    Max. Revolution  Balance quality grade G
                                                                                                                                                        (RPM)          ISO 1940-1 / 8821
R 1. When running the end mill and the face mill at revolutions exceeding the maximum revolution limit, the inserts or toolholder may be                                  (JIS B0905)
                         damaged due to the centrifugal force.                                                                                        ~20,000                 G16.0
                     2. For actual practical revolution, please set within recommended cutting condition.                                             ~30,000                  G6.3
                     3. When using at a higher revolution (over 10,000RPM), refer to the table to adjust the balance of MECX and suitable arbor.      30,000~                  G2.5

T  INDEX

                                                                                                                                                                                               EM8

   M8                                                                              kyocera@kyocera-tools.ru
                                                                                      www.kyocera-tools.ru