Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Turning Indexable Inserts (mm)
60°Triangle / Positive with Hole (mm) T d Description A T d
60°Triangle / Positive without Hole Description A TC_0902_ 5.56 2.38 2.5 7
TC_0601_ 3.97 1.59 - 7 TC_1102_ 6.35 2.38 2.8 7
TC_0802_ 4.76 2.38 2.3 7 TC_1103_ 6.35 3.18 2.8 7
B 60° AT P Free-Cutting Steel
r dM Classification of usage
Positive K
Insert TN6010N Carbon steel / Alloy steel
TN6020S : Interruption / 1st Choice
C H
D TN60 Stainless Steel
R PV7005 : Interruption / 2nd Choice
S PV7010
T PV7025 Gray Cast Iron
V CA5505 : Light Interruption / 1st Choice
W CA5515
CA5525 Nodular Cast Iron
CA5535 : Light Interruption / 2nd Choice
CA6515
CA6525 Non-ferrous Metals
CA4505 : Continuous / 1st Choice
CA4515
PR930 Heat-Resistant Alloys
PR1005 : Continuous / 2nd Choice
PR1025
PR1125 Titanium Alloy
PR1225 (In case hardness is under 45HRC)
PR1305
PR1310 Hard materials
PR1325
KW10Dim.CermetMEGACOATPVD CoatedMEGACOAT
SW05(mm)CermetCarbide
Ref. Page for
Toolholder
CVD Coated Carbide Carbide
Insert Description Applicable
Chipbreaker Range
Handed insert r
shows L-Hand (ap indicates radius)
Super Fine TCET 0802003F -USF 0.03
080201F -USF 0.1
080202F -USF 0.2
Insert (Turning) TCET 1103003F -USF 0.03
Low Feed 110301F -USF 0.1
110302F -USF 0.2
TCET 0802005MF -USF < 0.05 (mm)
080201MF -USF < 0.1 4 (Steel / Edge Length=08,09,11)
080202MF -USF < 0.2
U 11
TCET 1103005MF -USF < 0.05 ap 3
110301MF -USF < 0.1
Sharp Edge / Precision 110302MF -USF < 0.2 E27 U 08
2
HQ
1
TCGT 080201E -U 0.1 0.1 0.2 0.3 0.4
080202E -U 0.2 f (mm/rev)
Low Feed TCGT 110301E -U 0.1
110302E -U 0.2
110304E -U 0.4
TCGT 080201ME -U < 0.1
080202ME -U < 0.2
With Honing TCGT 110301ME -U < 0.1
110302ME -U < 0.2
110304ME -U < 0.4
Finishing TCGT 110201 0.1 F41
110202 0.2
110204 0.4
Non-ferrous Metals TCGT 110302 -A3 0.2 ap ap(mm) (Non-ferrous Metals)
110304 -A3 0.4 2 A3
1
Finishing-Medium / Sharp Edge 0.1 0.2 0.3 0.4
f (mm/rev)
TCGW 080201
Cast Iron 080202 0.1
0.2
TCGW 110301
110302 0.1
Without Chipbreaker 110304 0.2
0.4
(mm) (Steel)
1
Finishing TCGR 060102 -F 0.2 - 0.5
060104 -F 0.4 F
0.05 0.1 0.15 0.2
f (mm/rev)
Cast Iron TCGN 060102 0.2 -
060104 0.4
Without Chipbreaker
Insert whose corner R(r) dimension expressed with less than sign (e.g.<0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R (r).
TN30 PV30 PV60 PV90 PV7020 Reference Page B65
CA4010 CA4115 CA4120 PR915 PR905
B64 Inserts are sold in 10 piece boxes.
: Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) : Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocra-tools.ru